电源线束与电瓶干涉 后处理模块传感器支架螺纹孔锈蚀 车身后锁体划伤 车

Battery power harness interference <br>aftertreatment module screw hole corrosion sensor holder <br>body after scratching lock <br>door frame color decorative board buckle <br>left rearview mirror support sheath not snap into place <br>high-low tube with a fixed pull loose <br>logo scratched <br>A column drip channel modification <br>copilot floor sheath into place not <br>relay cover is not mounted in place <br>high intake air cleaner elbow bellows offset <br>rims corrosion <br>right axle shaft head scratch <br>frame missing tail boom harness fixing temperature sensor <br>accumulator pipe lack of fixed <br>accumulator pipe frame with an interference screw head <br>inside the left side member fixed to the trachea at least <br>the left side member loose inside the wire harness fixing drawstring <br>ABS solenoid valve interference with the ABS harness <br>air cleaner scratch <br>fuel tank identification flagging <br>the engine and fuel playing wire pipe support interfere with <br>urea water and heating the interference engine support <br>tie rod screw hole drop arm corrosion <br>right headlamp harness less a fixed <br>sub-tank outlet pipe and the cold intake pipe clamp screws for dynamic interference <br>rear mounting latching tubing lack the tee fixed <br>turning alarm buzzer harness interference fender <br>rear combination lamp harness interfering with the air reservoir <br>dryer wire harness fixing missing <br>left front fender deformation of <br>the door frame with the door attached to the apex gap unevenness <br>visor folds <br>sub dashboard scratch the <br>dome light is not installed in place<br>Electric overhead file cabinet blockages gap unevenness <br>clutch booster pump tube folds <br>air filter clogging alarm bead wire harness <br>after the harness hanging sheath lock release switch <br>transmission power take long pipe <br>bridge wire harness fixing bracket corrosion <br>of the engine and downcomers The wing edge gap of the frame is 7mm smaller. The <br>height of the vehicle is actually measured 3150. The announcement parameter is 3360.

Power harness and battery interference <br>Reprocessing module sensor support threaded hole rust <br>Body rear lock body scratch <br>Door frame trim board snap color difference <br>Left mirror mount housing not stuck in place <br>High and low gas pipe fixed pull-belt pine <br>Car sign scratch <br>A-pillar flow sink deformation <br>Co-pilot floor leather not in place <br>Relay cover is not in place <br>High-level intake bellows and empty filter elbow dislocation <br>Steel ring rust <br>Scratch on the right side of the bridge <br>The frame tail beam temperature sensor harness is not fixed <br>Air-storage tube lack of fixed <br>Air-storage tube and frame screw head interference <br>Less fixed inside the inner tube of the left vertical beam <br>Left vertical beam inner harness fixed pull-belt loose <br>ABS solenoid harness and ABS valve body interference <br>Empty filter scratch <br>Fuel tank identification is upsand <br>Engine iron line and fuel pipe bracket interference <br>Urea heating pipe and engine support interference <br>Steering lever hanging arm threaded hole rust <br>Right headlamp harness less fixed <br>Dynamic interference between the secondary water tank outlet pipe and the in-cooler inlet clamp screw <br>Lack of fixing at the three-way of the rear suspension locking pipe <br>Turn alarm buzzer harness and fender interference <br>Rear combination lamp harness and air reservoir interference <br>Dryer harness is not secured <br>Left front fender deformation <br>Uneven gaps between door frame strips and door fit <br>Sun visor folds <br>Sub-meter gauge scratch <br>Top light not in place <br>Top file cabinet electrical plug gap uneven <br>Clutching power pump trachea creases <br>Empty filter clogging alarm harness edge <br>Rear suspension lock switch harness sheath disengaged <br>Transmission extractor trachea length <br>Middle bridge harness retention bracket rust <br>A small 7mm gap between the engine under the water pipe and the wing edge of the frame <br>Vehicle height measured 3150, announcement parameter 3360

Interference between power harness and battery<br>Rust corrosion on threaded hole of sensor bracket of aftertreatment module<br>Body rear lock body scratch<br>Color difference of door frame decorative board buckle<br>Left rearview mirror mount guard not stuck in place<br>The fixed tension strap of high and low gas pipes is loose<br>Logo scratch<br>Deformation of A-pillar flume<br>Copilot's floor leather is not installed in place<br>Relay cover not in place<br>High level intake bellows and air filter elbow misplaced<br>Steel ring rusted<br>The right axle head of the middle bridge is scratched<br>Frame tail beam temperature sensor harness is not fixed<br>Lack of fixation of air pipe of air reservoir<br>Air reservoir air pipe interferes with frame screw head<br>Less fixation of inner air tube of left longitudinal beam<br>Left longitudinal beam inner harness fixing tension belt is loose<br>ABS solenoid valve harness interferes with ABS valve body<br>Scratched air filter<br>Fuel tank mark trimming<br>Engine iron wire interferes with fuel pipe bracket<br>Interference between urea heating water pipe and engine support<br>Rust corrosion on the threaded hole of steering rod pitman arm<br>The right headlamp harness is less fixed<br>Dynamic interference between the outlet pipe of the auxiliary water tank and the clamp screw of the intake pipe of the intercooler<br>Rear mount locking oil pipe tee is not fixed<br>Harness of turn alarm buzzer interferes with fender<br>Interference between rear combination lamp harness and air reservoir<br>Dryer harness is not fixed<br>Front left wheel fender deformed<br>Uneven gap between door frame rubber strip and door joint<br>Sunvisor fold<br>Scoring of auxiliary instrument panel<br>Ceiling lamp not installed in place<br>The gap of the electrical cover of the overhead filing cabinet is uneven<br>Clutch booster pump air pipe fold<br>Air filter blocking alarm harness crimping<br>The rear suspension lock switch harness sheath is disconnected<br>Transmission power take-off air pipe length<br>Fixed bracket of middle bridge harness rusted<br>The clearance between the engine water pipe and the flange edge of the frame is less than 7mm<br>Measured vehicle height 3150, announced parameter 3360<br>