3·紧固前下视镜时气螺刀与车门边沿干涉，紧固后产生划伤；4·调整限位器

3. The air screwdriver interferes with the edge of the door when tightening the front lower-view mirror, resulting in scratches after tightening; <br>4. Adjust the stopper bolt installation process so that the door can be closed when the front lower-view mirror is installed to avoid interference points; <br>5. Since there is no limit when disassembling the door, the door will scratch the A-pillar after disassembly, causing the edge of the door to be scratched; <br>6. Before disassembling the door, add a U-shaped sheath at the contact point between the door and the A-pillar to avoid the door sheet metal and the A-pillar. a sheet metal interference, the sheath is removed after the disassembly of the door, repeated use; <br>7. manipulator mounted door block wear protective glue, exposing a fixing bolt, the bolt along the bottom when placed in contact with the door, resulting in wear along the bottom; <br>8.4 months to replace gum If the block is worn out, temporarily use sponge pads, cloth strips and tape for protection to avoid interference between the door and the fixing bolts of the rubber block; <br>9. The protective rubber block of the door manipulator is worn out and the fixing bolts are exposed. When the door is placed, the bottom edge of the Edge wear; <br>11. Temporarily use waste paste parts to protect the air screwdriver to avoid rigid interference between the air screwdriver and the inner side of the door;

3. When fastening the front and lower mirrors, the air screw knife interferes with the edge of the door, resulting in scratches after fastening;<br>4. Adjust the bolt installation process of the stopper so that the door can be closed and the interference point can be avoided when installing the front lower mirror;<br>5. When removing the door, because there is no limit, the door scrapes against the A-pillar after removal, resulting in scratches on the edge of the door;<br>6. Before removing the door, add a U-shaped sheath at the contact point between the door and the A-pillar to avoid interference between the door sheet metal and the A-pillar sheet metal. After removing the door, remove the sheath and reuse it;<br>7. The protective rubber block of the manipulator for installing the door is worn, exposing the fixing bolt. When placing the door, the bottom edge contacts the bolt, resulting in the wear of the bottom edge;<br>The rubber block replaced in August and April has been worn. Sponge pad, cloth strip and adhesive tape are temporarily used for protection to avoid interference between the door and the fixing bolts of the rubber block;<br>9. The protective rubber block of the manipulator for installing the door is worn, exposing the fixing bolt. When placing the door, the bottom edge contacts the bolt, resulting in the wear of the bottom edge;<br>11. Temporarily use discarded adhesive parts to protect the air screw knife from hard interference with the inner side of the door;<br>

3. When fastening the front lower mirror, the air screw knife interferes with the edge of the door, resulting in scratches after fastening; 4. Adjust the bolt installation procedure of the stopper so that the door can be closed and the interference points can be avoided when installing the front lower mirror; 5. When removing the door, because there is no limit, the door rubs against the A-pillar after removal, causing the edge of the door to be scratched; 6. Add a U-shaped sheath at the contact point between the door and the A-pillar before disassembling the door to avoid interference between the door sheet metal and the A-pillar sheet metal. Remove the sheath after disassembling the door and reuse it; 7. The protective rubber block of the manipulator for installing the door is worn, and the fixing bolt is exposed. When the door is placed, the bottom edge is in contact with the bolt, resulting in wear of the bottom edge; The rubber blocks replaced in August and April are worn out, so sponge pads, cloth strips and adhesive tapes are temporarily used for protection, so as to avoid interference between the door and the fixing bolts of the rubber blocks; 9. The protective rubber block of the manipulator for installing the door is worn, and the fixing bolt is exposed. When the door is placed, the bottom edge is in contact with the bolt, resulting in wear of the bottom edge; 11. Temporary use of discarded sticking parts to protect the air screw knife to avoid hard interference between the air screw knife and the inside of the car door;