员工平安时刻关注 施工安全警钟长鸣木工加工区木工加工棚加工棚标识牌样式1.1.3.15钢筋加工棚(1)钢筋加工棚要求(a)采用工具式钢结构配的英语翻译

员工平安时刻关注 施工安全警钟长鸣木工加工区木工加工棚加工棚标识牌样式

员工平安时刻关注 施工安全警钟长鸣木工加工区木工加工棚加工棚标识牌样式1.1.3.15钢筋加工棚(1)钢筋加工棚要求(a)采用工具式钢结构配件现场组拼使用,主要标准配件有立柱、横梁、悬挑梁和螺栓连接组装,搭设尺寸12000mm(长)*5000mm(宽)*4000mm(高)。(b)采用100mm 厚C15混凝土硬化,在每根立柱下浇筑800*800*1000mmC15混凝土柱。(c)采用国标A150mm钢管作为立柱,立柱底端满焊10mm 厚600*600的钢板,用4块10mm 三角厚钢板满焊加固,钢管底部采用地脚螺栓固定。(d)立柱顶部各焊接焊接一块400*400铁板,立柱与立柱之间用2根长12m的18#工字钢并排连接固定,在工字钢顶部共焊接4根长5m 的10#工字钢,在圆立柱2m 高处焊接10#工字钢斜撑。(e)顶部主架宽5m、长12m、高80cm,骨架为钢管。钢管上顶层铺设一层脚手板,底层铺设一层胶合板防护,周围设置14厚胶合板封闭。(f)加工棚立柱涂刷400mm红白相间警示漆。(g)加工区域内配电箱设置、线缆敷设满足规范要求并保证设备安全用电要求,通过型钢立柱穿孔敷设电线,并统一高度设置设备开关箱,确定好钢筋套丝机、钢筋弯曲机、钢筋调直机等机械的位置,将其用电电线穿管预埋到C15混凝土中。(h)棚顶四周悬挂标语牌,内侧悬挂机械设备安全操作规程牌,安全标语牌高度为800mm,安全操作规程牌包括钢筋调直机、钢筋切断机、钢筋弯曲机、套丝机、切割机等机具安全操作规程牌,尺寸为(长*高)600*900mm。(2)钢筋加工棚图纸(a)平面图与侧面图:水平纵向10#钢槽冰平2条18#工字钢斜撑10#槽钢(b)正面图与标识:满铺脚手板满铺胶合板400x400钢板Φ48mm钢板Φ150mm钢管立柱10mm厚600x600的钢板钢筋加工区(c)钢筋加工棚实景图:杜绝违章操作 保证人生安全(3)钢筋原材存放
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
Ping An employee always pay attention to <br>construction safety alarm bells ringing <br>Wood Processing Zone <br>woodworking shed <br>processing shed signage style <br>1.1.3.15 steel processing shed <br>(1) shed steel processing requirements <br>(a) be instrumental Steel Accessories group to fight the use of the site, the main standard accessories there are columns, beams, cantilever beams and bolted assembly, erection 12000mm size (length) * 5000mm (width) * 4000mm (height). <br>(B) using 100mm thick cured concrete C15, 800 * 800 * 1000mmC15 pouring concrete columns in each column. <br>(C) as a national standard A150mm steel column, 10mm thick fully welded bottom plate uprights 600 * 600, with four triangular 10mm thick steel fully welded reinforcement, the bottom pipe by using a fixing bolt. <br>(D) between the top of each column-welded to an iron plate 400 * 400, column 2 and column with 18 # 12m long beam is connected and fixed side by side, on the top beam welding total length of 5m four work 10 # type steel, the round post 10 # 2m high beam welding strut. <br>(E) the top of the main frame width 5m, length 12m, high 80cm, steel skeleton. <br>Laying a layer of steel tube scaffold top plate, the bottom layer of plywood laying protection 14 is provided around the closed thick plywood. <br>(F) processing shed 400mm column painted red and white warning paint. <br>The (g) setting the processing region distribution box, cable laying equipment to meet the regulatory requirements to ensure the safety and power requirements, by laying perforated steel column wires, and the switch box uniform height setting device, to determine a good threading machine steel, steel bending machine position, bar straightening machine mechanical, electrical wires through the pipe to be embedded into the concrete C15.<br>(H) Ceiling placard hanging around the inner suspension mechanical equipment safety procedures card, security placards height of 800mm, safe operation card comprises bar straightening machine, steel cutting machine, steel bending machine, threading machine, cutting machine licensing procedures and other safety equipment, size (L * H) 600 * 900mm. <br>(2) sheet steel processing shed <br>(a) a plan view and a side view: <br>the horizontal longitudinal grooves 10 # steel <br>ice level 2 18 # I-beam <br>strut channel # 10 <br>(b) front view and identification: <br>paved scaffold board <br>paved plywood <br>400x400 steel <br>Φ48mm plate <br>Φ150mm tubular column <br>10mm thick steel plate 600x600 <br>steel processing zone <br>(c) of FIG real shed steel processing: <br>to prevent illegal operation to ensure the safety of life <br>(3) reinforced raw material storage
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
Employees' Peace At All Time Attention <br>Construction safety alarm bells ringing<br>Carpentry Processing Zone<br>Carpentry workshop<br>Processing shed sign style<br>1.1.3.15 Rebar Processing Shed<br>(1) Rebar processing shed requirements<br>(a) The use of tool-based steel structure accessories on-site group use, the main standard accessories are columns, beams, suspension beams and bolts connected assembly, set up a size of 12000mm (l) x 5000mm (w) x 4000mm (high).<br>(b) Hardened with 100mm thick C15 concrete, pouring 800 x 800 x 1000mm C15 concrete columns under each pillar.<br>(c) the use of national standard A150mm steel pipe as a column, the bottom end of the column full welding 10mm thick 600 x 600 steel plate, with 4 pieces of 10mm triangular thick steel plate full welding reinforcement, steel pipe bottom with foot bolts fixed.<br>(d) the top of the column welding a piece of 400 x 400 iron plate, between the column and the column with 2 long 12m of the 18-word steel side-by-side connection fixed, in the top of the work-word steel welded a total of 4 5m long 10- of the 10-word steel, in the column 2m high welding 10 s- steel oblique.<br>(e) The top main frame is 5m wide, 12m long and 80cm high, and the skeleton is steel pipe.<br>The top layer of steel pipe is laid a foot plate, the bottom layer is laid a layer of plywood protection, surrounded by 14 thick plywood closed.<br>(f) Processing shed columns painted with 400mm red and white warning paint.<br>(g) in the processing area distribution box settings, cable laying to meet the specification requirements and ensure the safety of equipment electricity requirements, through the type of steel column perforated wire, and unified height setting equipment switch box, to determine the location of steel wire set machine, steel bending machine, rebar straightening machine and other machinery, its electrical wires through the tube pre-buried in C15 concrete.<br>(h) hanging placards around the roof, the inside hanging machinery and equipment safety operating procedures, safety placard height of 800mm, safety operating procedures card including rebar straightening machine, rebar cutting machine, rebar bending machine, wire set machine, cutting machine and other implement safety operating procedures card, size (long x high) 600 x 900mm.<br>(2) Steel processing shed drawings<br>(a) Floor and side:<br>Horizontal portrait 10 s slot<br>Ice flat 2 bars 18 s work-word steel<br>Sloping 10 slot steel<br>(b) Front map and logo:<br>Full of foot-and-hand plates<br>Full plywood<br>400x400 steel plate<br>48mm steel plate<br>150mm steel tube column<br>10mm thick 600x600 steel plate<br>Rebar processing area<br>(c) A live view of the rebar processing shed:<br>Put an end to illegal operations to ensure the safety of life<br>(3) Rebar raw material storage
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
Employees always pay attention to safety<br>Construction safety alarm<br>Woodworking area<br>Woodworking shed<br>Processing shed sign pattern<br>1.1.3.15 reinforcement processing shed<br>(1) Requirements for steel processing shed<br>(a) The tool type steel structure fittings are assembled on site. The main standard fittings are column, beam, cantilever beam and bolt connection and assembly. The erection size is 12000mm (L) × 5000mm (W) × 4000mm (H).<br>(b) Use 100mm thick C15 concrete to harden, and pour 800 * 800 * 1000mm C15 concrete column under each column.<br>(c) The national standard a150mm steel pipe is used as the column. The bottom of the column is fully welded with 10 mm thick 600 * 600 steel plate. Four 10 mm triangular thick steel plates are fully welded for reinforcement. The bottom of the steel pipe is fixed with anchor bolts.<br>(d) A 400 * 400 iron plate is welded on the top of the column. Two 12m long 18 ා I-beams are used to connect and fix the column and the column side by side. Four 5m long 10 ා I-beams are welded on the top of the I-beam, and 10 ා I-beam diagonal braces are welded on the 2m height of the round column.<br>(e) The top main frame is 5m wide, 12m long and 80cm high, and the skeleton is steel pipe.<br>A layer of scaffold board shall be laid on the top layer of steel pipe, and a layer of plywood shall be laid on the bottom layer for protection, and 14 thick plywood shall be set around for sealing.<br>(f) The column of processing shed shall be painted with 400mm red and white warning paint.<br>(g) The distribution box and cable laying in the processing area shall meet the specification requirements and ensure the safe power consumption of the equipment. The wires shall be laid through the holes in the section steel column, and the equipment switch box shall be set at a uniform height. The positions of the steel bar threading machine, steel bar bending machine, steel bar straightening machine and other machines shall be determined, and the electric wires shall be embedded in C15 concrete through pipes.<br>(h) The placard is hung around the ceiling, and the safety operation regulation plate of mechanical equipment is hung inside. The height of the safety placard is 800mm. The safety operation regulation plate includes the safety operation regulation plate of the steel bar straightening machine, steel bar cutting machine, steel bar bending machine, threading machine, cutting machine and other machines and tools, and the size is (length * height) 600*900mm.<br>(2) Reinforcement processing shed drawing<br>(a) Plan and profile:<br>Horizontal and longitudinal 10 × steel groove<br>Ice flat 2 18 × I-beam<br>Diagonal bracing 10 × channel steel<br>(b) Front view and logo:<br>Fully covered scaffold board<br>Full ply plywood<br>400X400 steel plate<br>48mm steel plate<br>Φ 150 mm steel pipe column<br>10 mm thick 600x600 steel plate<br>Reinforcement processing area<br>(c) Actual view of reinforcement processing shed:<br>Put an end to illegal operation to ensure life safety<br>(3) Steel bar raw material storage
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: