车门边沿划伤 仪表台左下裙板未装到位 车门内饰板装不到位 后视镜底座护

Door edge scratches <br>dashboard lower left skirt is not installed in place <br>of the door trim board is not installed in place <br>of the mirror base sheath pine <br>gussets heteroaryl paint <br>front panel paint finish heteroaryl <br>shift flexible shaft and the reverse interfering carrier <br>surrounding the power distribution box before lack harness fixing <br>the bumper fascia plate fixing bolt deletion <br>foot trim panel mounted in place <br>sub tank level is low <br>copilot floor sheath into place not <br>stubs corroded <br>battery cover does not match the battery compartment <br>the battery cover modification <br>power line and grounding line cROSS interferometer <br>bridge mudguard bracket corrosion <br>reversing buzzer harness connector sheath off <br>the rear splash plate is deformed <br>after the airbag trachea and the axle bearing thrust rod interfering <br>multi-way valve fixed tube missing <br>air cleaner hose connection no-tight attachment brackets the amount of <br>the regulating valve balloon overhang less fixing pipe <br>reversing mechanism control harness retarder steel interference <br>urea injection tube and the air filter bracket interference <br>windshield drain bolt bracket cotton pad means Ohira <br>air horn to the engine block duct interference <br>pipes under the sub-tank intercooler and intake pipe clamp dynamic interference <br>gas shortage harness fixing horn <br>air horn blow pipe joint <br>axle airbag after deformation <br>bridge stabilizer bar corrosion <br>state fireproof cover fixing clip tightening inconsistent <br>urea water and heating turbocharger small gap ( 60mm)<br>Front axle leaf spring with a small gap of the exhaust pipe (17mm) <br>peri scratch <br>copilot door window glass stopper pressed (right) <br>ceiling reading light is not bonded to <br>the ceiling panel and the inner fender control large gap <br>peri inner sheath false plate attached <br>around the edges of the wave front trim <br>copilot paper bags are not bonded, NA <br>retarder interfering transmission housing tube

Cut on the edge of the door <br>The lower left skirt of the gauge meter is not in place <br>Door interior panels are not in place <br>Rearview mirror base guard shell pine <br>Corner plate paint <br>Front panel paint <br>Shift soft shaft and flip mount interference <br>The front-wall edict harness is not fixed <br>Lack of bumper trim plate retention bolts <br>Foot decoration board is not in place <br>Low level of secondary water tank <br>Co-pilot floor leather not in place <br>Shaft head rust <br>Battery case lid does not match battery box <br>Battery case cap deformation <br>Power cord and tie-line cross interference <br>Mid-bridge fender bracket rust <br>Reversing buzzer harness plug guard shell off <br>Rear wheel splash plate deformation <br>Interference between the rear axle air bag trachea and the thrust rod support <br>Multi-pass valve trachea lack of fixed <br>Empty filter connected to the hose fixing clamp no retension amount <br>Less fixed post-suspension airbag control valve <br>Flip mechanism control harness and hydraulic retarder steel pipe interference <br>Urea injection tube and air filter bracket interference <br>Windshielded cotton bracket fixing bolt leak large flat mat <br>Air horn trachea and engine body interference <br>Dynamic interference between the sub-water tank under the water pipe and the in-cold pipe clamp <br>Air horn harness is not secured <br>Air horn gas joint leak <br>Rear axle airbag deformation <br>Middle bridge stabilizer bar rust <br>Inconsistent tight state of fire cover fixing clamps <br>Small urea heating pipe with turbocharger clearance (60mm) <br>Small gap between front axle reed and exhaust pipe (17mm) <br>Back circumference scratch <br>Co-pilot door glass squeeze window limit block (right) <br>Ceiling reading light does not fit <br>Large gap between the roof control panel and the inner guard <br>The back inner guard is not pasted <br>Front-panel interior panel edge wave <br>Co-pilot file bag does not fit, does not apply <br>Hydraulic retarder water pipe and transmission housing interference

Door edge scratch<br>Left lower apron of instrument panel is not installed in place<br>Door interior trim panel is not installed in place<br>Rear view mirror base cover loose<br>Corner board mixed paint<br>Front panel paint miscellaneous<br>Interference between shift flexible shaft and turnover support<br>Front wall power distribution box harness is not fixed<br>Fixed bolt of bumper trim panel is missing<br>Foot pedal trim not in place<br>Low level of auxiliary water tank<br>Copilot's floor leather is not installed in place<br>Shaft head rusted<br>Battery box cover does not match battery box<br>Battery box cover deformed<br>Cross interference between power line and ground line<br>Mudguard bracket of middle bridge rusted<br>The harness plug of reversing buzzer falls off<br>Rear wheel splash guard deformed<br>Rear axle air bag air pipe interferes with thrust rod support<br>Multi way valve air pipe is not fixed<br>The fixed clamp of air filter connecting rubber tube has no tightening amount<br>Less fixation of air pipe of rear suspension air bag regulating valve<br>Interference between control harness of turning mechanism and hydraulic retarder steel pipe<br>Interference between urea injection pipe and air filter bracket<br>The fixing bolt of the windshield cotton bracket is missing to install a large flat pad<br>Interference between gas pipe of air horn and engine body<br>Dynamic interference between the lower water pipe of the auxiliary water tank and the intake pipe clamp of the intercooler<br>Air horn harness is not fixed<br>Air leak at air horn air pipe connector<br>Rear axle airbag deformation<br>Middle bridge stabilizer bar rusted<br>The fastening state of fixing clamp of fire hood is inconsistent<br>Small clearance between urea heating water pipe and turbocharger (60mm)<br>Small gap between front axle leaf spring and exhaust pipe (17mm)<br>Rear wall scratch<br>Passenger's door glass squeezing window stop (right)<br>Ceiling reading lamp does not fit<br>Large gap between ceiling control panel and inner guard board<br>The back wall inner guard board is not pasted firmly<br>Front wall interior trim panel edge wave<br>Copilot's file bag does not fit and is not applicable<br>Hydraulic retarder water pipe interferes with transmission case