电气主接线的设计应根据变电所在电力系统中的地位、负荷性质、出线数量、设

电气主接线的设计应根据变电所在电力系统中的地位、负荷性质、出线数量、设备特点、周围环境和变电所的规划容量，满足供电可靠性、运行灵活、操作方便、节省投资和扩建的要求。具体如下： 1．变电站的高压侧接线，根据技术设计规程应尽量采用断路器较少或不用断路器的接线方式。 2．在10kV配电装置中，当线路在6回及以上时，根据规程一般采用单母线分段接线方式。

0/5000

源语言: -

目标语言: -

结果 (英语) 1: [复制]

复制成功！

The design of the electrical main wiring should be based on the status, load nature, number of outlets, equipment characteristics, surrounding environment and planned capacity of the substation in the power system where the substation is located, to meet the reliability of power supply, flexible operation, easy operation, saving investment and expansion Requirements. The details are as follows: 1. According to the technical design regulations, the wiring of the high-voltage side of the substation should be connected with fewer or no circuit breakers. 2. In the 10kV distribution device, when the line is 6 or more times, the single bus section wiring method is generally used according to the regulations.

正在翻译中..

结果 (英语) 2:[复制]

复制成功！

The design of the main electrical wiring should meet the requirements of power supply reliability, flexible operation, convenient operation, saving investment and expansion according to the position, load nature, number of lines out, equipment characteristics, environment and power substation planning capacity in the power generation system. Here's how: 1. Substation high-voltage side wiring, according to technical design procedures should be as far as possible to use less circuit breakers or no circuit breaker wiring. 2. In a 10kV power distribution unit, when the line is 6 times and above, according to the procedures generally use a single-bus segmented wiring method.

正在翻译中..

结果 (英语) 3:[复制]

复制成功！

The design of electrical main wiring shall meet the requirements of power supply reliability, flexible operation, convenient operation, investment saving and expansion according to the position of the power system where the substation is located, load nature, number of outgoing lines, equipment characteristics, surrounding environment and planned capacity of the substation. The details are as follows: 1. According to the technical design specification, the high-voltage side wiring of the substation shall try to adopt the wiring mode of less breakers or no breakers. 2. In 10kV power distribution device, when the line is 6 circuits or more, the single bus section connection mode is generally adopted according to the regulations.

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.