设备组装完毕后，设备先进行试运转，确保载荷能正常运转，无故障发生。一、

设备组装完毕后，设备先进行试运转，确保载荷能正常运转，无故障发生。一、插好电源插座接通电源。二、将手动/自动开关选到手动挡分别单独启动提升机、搅龙、拨粮轮和风机，观察有无异常，确认无异常后将手动/自动开关打到自动上进行调试。三、启动“进料”按钮（1）提升机和上搅龙及散粮器、下搅龙顺序起动，观察有无异常；（2）检查各运转部位有无异常噪音；

0/5000

源语言: -

目标语言: -

结果 (英语) 1: [复制]

复制成功！

After the equipment is assembled, the equipment will be put into trial operation to ensure that the load can operate normally and no failures occur. 1. Plug in the power socket and turn on the power. 2. Select the manual/auto switch to the manual gear to separately start the hoist, agitator, grain dial and fan, observe whether there is any abnormality, and after confirming that there is no abnormality, turn the manual/auto switch to automatic for debugging. 3. Start the "Feeding" button (1) The elevator and the upper agitating dragon, bulk grain dispenser and lower agitating dragon are started in sequence, and observe whether there is any abnormality; (2) Check whether there is any abnormal noise in each running part;

正在翻译中..

结果 (英语) 2:[复制]

复制成功！

After the equipment is assembled, the equipment is first commissioned to ensure that the load can operate normally and there is no failure. First, plug in the power outlet to power on. Second, the manual/automatic switch selected to the manual stop Separately start the lifter, stir the dragon, dial grain wheel and fan, observe whether there are anomalies, confirm that no abnormality will be manual / automatic switch to automatic commissioning. Third, start the "feed" button (1) the lifter and the upper stir-up dragon and the bulker, the next stir-up dragon sequence start, observe whether there are any abnormalities; (2) check each operating site for abnormal noise;

正在翻译中..

结果 (英语) 3:[复制]

复制成功！

After the equipment is assembled, the equipment shall be put into trial operation to ensure that the load can run normally without any fault. 1、 Plug in the power socket and turn on the power. 2、 Set the manual / automatic switch to manual Start the hoist, auger, grain wheel and fan separately, observe whether there is any abnormality, and then turn the manual / automatic switch to automatic for debugging. 3、 Activate the "feed" button (1) Hoist, upper auger, bulk grain device and lower auger are started in sequence to observe whether there is any abnormality; (2) Check whether there is any abnormal noise in the running parts;

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.