在编程软件和仿真软件对控制程序调试时，根据所设计的关于搅拌控制的梯形图

在编程软件和仿真软件对控制程序调试时，根据所设计的关于搅拌控制的梯形图，选用PLC 的S7-200 的仿真软件进行仿真。具体步骤如下:(1)首先把仿真软件的CPU226 (点CONFIGURACION-TIPO DE CPU,然后点Accepter)；(2)导入梯形图；(3)点击运行；(4)进行调试。观察仿真软件上的灯是否按照程序要求依次点亮，延时是否准确。是就说明程序正确，不是就说明程序还存在问题。

0/5000

源语言: -

目标语言: -

结果 (英语) 1: [复制]

复制成功！

When the programming software and the simulation software debug the control program, the simulation software of the S7-200 of PLC is used for simulation according to the designed ladder diagram about the stirring control. The specific steps are as follows: (1) First, put the CPU226 of the simulation software (click CONFIGURACION-TIPO DE CPU, then click Accepter); (2) import the ladder diagram; (3) click run; (4) debug. Observe whether the lights on the simulation software are lit sequentially according to the program requirements, and whether the delay is accurate. It means that the program is correct, not that the program still has problems.

正在翻译中..

结果 (英语) 2:[复制]

复制成功！

In the programming software and simulation software to the control program debugging, according to the design of the ladder map on stirring control, the use of PLC S7-200 simulation software for simulation. Here are the steps: (1) First put the simulation software CPU226 (point CONFIGURACION-TIPO DE CPU, and then point Accepter); (2) Import ladder; (3) Click to run; (4) Debug. Observe whether the lights on the simulation software are lit in turn according to the requirements of the program, and whether the delay is accurate. It is to state that the procedure is correct, not that there is a problem with the procedure.

正在翻译中..

结果 (英语) 3:[复制]

复制成功！

When the program and simulation software debug the control program, according to the designed ladder diagram about mixing control, S7-200 simulation software of PLC is selected for simulation. The specific steps are as follows: (1) Firstly, cpu226 (point configuration-tip de CPU, then point accepter) of the simulation software is used; (2) Import ladder; (3) Click Run; (4) Conduct debugging. Observe whether the lights on the simulation software turn on in order according to the program requirements, and whether the delay is accurate. It means that the program is correct, not that there are still problems in the program.

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.