Standby charge storage environment – Set the Temp/Humidity chamber to 的简体中文翻译

Standby charge storage environment

Standby charge storage environment – Set the Temp/Humidity chamber to 40 +/- 2 °C with 90%~95%RH. Remove the units from the Salt Spray chamber, the units should be powered on and connect with standard chargers inside the Temp/Humidity chamber and store them for 18 hours. The USB cable used for charging should be inspected to ensure no obvious connector corrosion and make sure the charging function is good. The cable will collect some salt from testing units. If the cables have been used many times, then the cable itself may have degraded, and may affect the test device results. If corrosion or charging function issue was found, the cable need to be changed as soon as possible. Remove the units from the chamber and let the units sit at room temperature for 1-2 hours to completely dry off and discharge the units to 20%~30% battery power. Observe the state of USB port by using a microscope and take pictures (both sides of the USB port need to be taken). Perform 10 cycles of USB insertion and then take a basic manual function test on all units (i.e. charging, data transmission and OTG functionality). Record any failures and/or observations including cosmetic failures using the template located on Appendix A below. This completes the first loop of this test. Note: Please use new in-box USB cable for USBC functional check during the whole test.
0/5000
源语言: -
目标语言: -
结果 (简体中文) 1: [复制]
复制成功!
Standby charge storage environment – Set the Temp/Humidity chamber to 40 +/- 2 °C with 90%~95%RH. Remove the units from the Salt Spray chamber, the units should be powered on and connect with standard chargers inside the Temp/Humidity chamber and store them for 18 hours. The USB cable used for charging should be inspected to ensure no obvious connector corrosion and make sure the charging function is good. The cable will collect some salt from testing units. If the cables have been used many times, then the cable itself may have degraded, and may affect the test device results. If corrosion or charging function issue was found, the cable need to be changed as soon as possible. Remove the units from the chamber and let the units sit at room temperature for 1-2 hours to completely dry off and discharge the units to 20%~30% battery power. Observe the state of USB port by using a microscope and take pictures (both sides of the USB port need to be taken). Perform 10 cycles of USB insertion and then take a basic manual function test on all units (i.e. charging, data transmission and OTG functionality). Record any failures and/or observations including cosmetic failures using the template located on Appendix A below. This completes the first loop of this test. <br>注意:在整个测试过程中,请使用新的内置USB电缆进行USBC功能检查。
正在翻译中..
结果 (简体中文) 2:[复制]
复制成功!
待机充电存储环境 – 将温度/湿度室设置为 40 °/- 2 °C,90%±95%RH。从盐喷雾室中卸下设备,设备应通电,并与温度/湿度室内的标准充电器连接,并存放 18 小时。应检查用于充电的 USB 电缆,以确保没有明显的连接器腐蚀,并确保充电功能良好。电缆将从测试单元收集一些盐。如果电缆已多次使用,则电缆本身可能已经降级,并可能影响测试设备的结果。如果发现腐蚀或充电功能问题,则需要尽快更换电缆。将装置从腔室中拆下,让装置在室温下坐1-2小时,完全干燥,将装置放电至20%~30%的电池功率。使用显微镜观察 USB 端口的状态并拍照(需要拍摄 USB 端口的两侧)。执行 10 个周期的 USB 插入,然后在所有装置(即充电、数据传输和 OTG 功能)上进行基本的手动功能测试。使用以下附录 A 上的模板记录任何故障和/或观察,包括表面故障。这将完成此测试的第一个循环。<br>注意:请使用新的盒内 USB 电缆进行 USBC 功能检查,整个测试期间。
正在翻译中..
结果 (简体中文) 3:[复制]
复制成功!
备用充电储存环境-将温度/湿度室设置为40+/-2°C,相对湿度为90%~95%。将装置从盐雾室中取出,装置应通电并与温度/湿度室内的标准充电器连接,并储存18小时。充电用USB线应检查无明显接头腐蚀,充电功能良好。电缆将从测试单元收集一些盐。如果电缆已多次使用,则电缆本身可能已退化,并可能影响测试设备的结果。如果发现腐蚀或充电功能问题,需要尽快更换电缆。将装置从试验箱中取出,在室温下放置1-2小时,使其完全干燥,并将装置放电至20%~30%的电池电量。用显微镜观察USB端口的状态并拍照(需要拍摄USB端口的两侧)。执行10个USB插入循环<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: