试注塑过程中,应详细记录模具状态和工艺参数,对不合格的模具应及时进行返修。模具的维护模具在使用过程中,会产生正常的磨损或不正常的损坏。不正常的英语翻译

试注塑过程中,应详细记录模具状态和工艺参数,对不合格的模具应及时进行返

试注塑过程中,应详细记录模具状态和工艺参数,对不合格的模具应及时进行返修。模具的维护模具在使用过程中,会产生正常的磨损或不正常的损坏。不正常损坏绝大多数是由于操作不当所致,例如嵌件没放稳就合模,致使型腔被打缺,或是型芯较细,当塑件脱模不下时,用手锤重力敲击而使型芯弯曲。总体来说有如下几种情况要注意:① 型芯或导向柱碰弯。② 型腔局部损坏,大部分仍是好的。③ 由于型腔材料硬度太底或制件精度太差,使用一段时期后分型面不严密,以致溢边太厚,影响制件质量。
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
During the trial injection process, the mold status and process parameters should be recorded in detail, and the unqualified mold should be repaired in time. <br>Maintenance of the <br>mold During the use of the mold, normal wear or abnormal damage will occur. The majority of abnormal damage is caused by improper operation, such as the mold is closed before the insert is stabilized, causing the cavity to be missing, or the core is thin. When the plastic part cannot be demolded, hammer it with a hammer Strike to bend the core. <br>In general, there are several situations to pay attention to: <br>① The core or guide post bends. <br>② The cavity is partially damaged, most of them are still good. <br>③ Because the hardness of the cavity material is too low or the precision of the parts is too bad, the parting surface is not tight after a period of use, so that the overflow edge is too thick, which affects the quality of the parts.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
In the process of test injection molding, the mold status and process parameters should be recorded in detail, and the unqualified mold should be repaired in a timely manner.<br>Maintenance of molds<br>Mold during use, will produce normal wear or abnormal damage. The vast majority of abnormal damage is due to improper operation, such as the insert did not stabilize the fit mold, resulting in the cavity is missing, or the core is fine, when the mold is not molded, with the hammer gravity knock and bend the core.<br>In general, there are several situations to be aware of:<br>(1) The core or guide column is bent.<br>(2) Partial damage to the cavity, most of which is still good.<br>(3) Because the cavity material hardness is too poor or the precision of the assembly is too poor, after the use of a period of time the parting surface is not tight, so that the overflow edge is too thick, affecting the quality of the assembly.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
During the injection test, the mold status and process parameters shall be recorded in detail, and the unqualified mold shall be repaired in time.<br>Mold maintenance<br>During the use of the mould, normal wear or abnormal damage will occur. Most of the abnormal damage is caused by improper operation, such as closing the mold when the insert is not placed stably, causing the cavity to be broken, or the core is relatively thin. When the plastic part cannot be demoulded, the core will be bent by hitting it with the hammer gravity.<br>In general, the following situations should be noted:<br>① Bending of core or guide post.<br>② Most of the cavity damage is good.<br>③ Because the hardness of the cavity material is too low or the accuracy of the part is too poor, the parting surface is not tight after a period of use, so the overflow edge is too thick, which affects the quality of the part.<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: