脱模机构如果操作不当,会影响塑件的整体质量,是注射成型过程中最后一个环节。 简单脱模机构通常包括推杆脱模机构和顶杆其原理是在机构的动模一边拖的英语翻译

脱模机构如果操作不当,会影响塑件的整体质量,是注射成型过程中最后一个环

脱模机构如果操作不当,会影响塑件的整体质量,是注射成型过程中最后一个环节。 简单脱模机构通常包括推杆脱模机构和顶杆其原理是在机构的动模一边拖加一次顶出力,从而实现塑件脱模。顶杆顶出塑件后,必须返回到顶出前的初始位置后,才能进行下一次的循环工作。因此,必须设计复位杆来实现往复循环。复位杆又称回程杆。顶杆大多采用T8A或T10A材料,头部淬火硬度大于50HRC,表面粗糙度是小于0.8μm的Ra值,和顶杆孔呈H8/f8配合。顶杆是模具表准件。复位回程杆回程。复位杆的端面与分型面保持齐平,在合模时,定模板推动复位杆,通过顶杆固定板,使顶杆恢复到顶出前的位置。复位杆必须安装在与固定杆相同的固定板上。
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
If the demoulding mechanism is improperly operated, it will affect the overall quality of the plastic parts and is the last link in the injection molding process. <br>Simple demoulding mechanism usually includes push rod demoulding mechanism and ejector rod. Its principle is to drag an ejection force on the moving mold side of the mechanism, so as to realize demoulding of plastic parts. <br>After the ejector ejects the plastic part, it must return to the initial position before ejection before the next cycle can be performed. Therefore, the reset lever must be designed to realize the reciprocating cycle. The reset lever is also called the return lever. <br>The jack is mostly made of T8A or T10A material, the head quenching hardness is greater than 50HRC, the surface roughness is less than 0.8μm Ra value, and the jack hole is H8 / f8. The ejector rod is the standard of the die watch. <br>Reset the return lever return. The end surface of the reset lever is kept flush with the parting surface. When the mold is closed, the fixed platen pushes the reset lever, and the plate is fixed by the jack to restore the jack to the position before being ejected. The reset lever must be installed on the same fixing plate as the fixing lever.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
If the release mechanism is not properly operated, it will affect the overall quality of the plastic parts, is the last link in the injection molding process. <br>Simple release mechanism usually includes the putter release mechanism and the top rod its principle is that the mechanism's moving mold side drags and adds a top output, so as to achieve the mold release.<br>After the top of the top rod has been molded, it must be returned to the initial position before the top out before the next cycle can be carried out. Therefore, the reset lever must be designed to implement the reciprocating cycle. The reset bar is also known as the return bar.<br>Most of the top rod steamed with T8A or T10A material, head quenching hardness is greater than 50HRC, surface roughness is less than 0.8 m of Ra value, and the top rod hole is H8/f8. The top bar is a mold table alignment.<br>Reset the return bar backhaul. The end face of the reset bar is flush with the patterned face, and when working, the fixed template pushes the reset lever and, through the top bar fixing the plate, restores the top rod to the position before the top. The reset lever must be mounted on the same fixed plate as the fixing rod.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
If the demoulding mechanism is operated improperly, it will affect the overall quality of the plastic part, which is the last step in the injection molding process.<br>A simple demoulding mechanism usually includes a push rod demoulding mechanism and a ejector rod. The principle is to drag and add a jacking force on the moving die side of the mechanism, so as to realize demoulding of plastic parts.<br>After the ejector pin ejects the plastic part, it must return to the original position before the ejector pin can carry out the next cycle work. Therefore, it is necessary to design a reset rod to realize the reciprocating cycle. The reset lever is also called the return lever.<br>T8A or T10A materials are mostly used for the ejector pin. The quenching hardness of the head is more than 50 HRC, and the surface roughness is Ra value less than 0.8 μ m, which is H8 / F8 matching with the ejector pin hole. Ejector pin is the standard part of mould.<br>Reset the return lever return. The end face of the reset rod shall be kept flush with the parting surface. When closing the mold, the fixed formwork shall push the reset rod through the fixed plate of the top rod to restore the top rod to the position before ejection. The reset lever must be installed on the same fixing plate as the fixing lever.<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: