16、开通五轴（之前第四轴、第五轴屏蔽了）。将油冷机报警信号重新开通。

16、开通五轴（之前第四轴、第五轴屏蔽了）。将油冷机报警信号重新开通。17、往润滑油泵内加入足够的G68号导轨油。18、对机床进行水平调整，对机床底部钣金补玻璃胶（为防万一）。19、放入机床水箱，安装机床水泵，接好机床尾部中置的接水盒和水管。20、往机床水箱加入切削液，装上工件，就可以进行试切了。说明：最好将X、Y轴钢板防护罩的位置重新调正下，以达到运行时防护罩的声音降低。

0/5000

源语言: -

目标语言: -

结果 (英语) 1: [复制]

复制成功！

16. Open the five axes (the fourth and fifth axes were shielded before). Turn on the oil cooler alarm signal again. 17. Add enough G68 rail oil to the lubricating oil pump. 18. Adjust the level of the machine tool and patch the glass glue on the bottom sheet metal of the machine tool (just in case). 19. Put in the water tank of the machine tool, install the water pump of the machine tool, and connect the water box and water pipe in the middle of the rear of the machine tool. 20. Add cutting fluid to the water tank of the machine tool, install the workpiece, and start trial cutting. Note: It is best to re-adjust the position of the X and Y-axis steel plate protective cover to reduce the sound of the protective cover during operation.

正在翻译中..

结果 (英语) 2:[复制]

复制成功！

16. Turn on the fifth axis (the fourth axis and the fifth axis were shielded before). Reopen the alarm signal of the oil cooler. 17. Add enough g68 guide rail oil into the lubricating oil pump. 18. Adjust the level of the machine tool, and fill the sheet metal at the bottom of the machine tool with glass glue (just in case). 19. Put it into the water tank of the machine tool, install the water pump of the machine tool, and connect the water receiving box and water pipe in the middle of the tail of the machine tool. 20. Add cutting fluid to the water tank of the machine tool, install the workpiece, and then the trial cutting can be carried out. Note: it is better to readjust the position of the x-axis and y-axis steel plate protective cover to reduce the sound of the protective cover during operation.

正在翻译中..

结果 (英语) 3:[复制]

复制成功！

16. Turn on the fifth axis (the fourth axis and the fifth axis were shielded before). Turn on the alarm signal of oil cooler again.17. add enough G68 guide rail oil into lubricating oil pump.18. horizontally adjust the machine tool and add glass glue to the sheet metal at the bottom of the machine tool (just in case).19. Put it into the water tank of the machine tool, install the water pump of the machine tool, and connect the water receiving box and water pipe in the middle of the tail of the machine tool.20. Add cutting fluid to the water tank of the machine tool, and mount the workpiece, and then try to cut it.Note: It is best to readjust the position of the X-axis and Y-axis steel shield to lower the sound of the shield during operation.

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.