按照挤出机组的操作流程如下:1.开机前,衣服穿着整齐,戴好劳保防护,禁止腰系绳带,严禁披衣、穿短裤、穿拖鞋上岗;2.开机前,检查喂料口有无杂的简体中文翻译

按照挤出机组的操作流程如下:1.开机前,衣服穿着整齐,戴好劳保防护,禁

按照挤出机组的操作流程如下:1.开机前,衣服穿着整齐,戴好劳保防护,禁止腰系绳带,严禁披衣、穿短裤、穿拖鞋上岗;2.开机前,检查喂料口有无杂物,下班时喂料口需用盖板盖住,防止杂物落入挤出机内;3.预热机头、机身、口型、芯型、清理标识线装置;预热带好防护用品,防止烫伤。预热达到工艺要求后关闭蒸气压力;4.安装与规格相匹配的口型、芯型并锁紧,调整到规定的位置,保证胎筒的厚度均匀;5.打开总电源,检查电气系统正常、操作控制系统灵敏可靠,开启油泵,检查油泵是否正常工作,润滑油是否流畅,听运转部位是否有异常声音;6.启动主机,开启机头、机身、小辊筒、螺杆的全部冷却水,然后再送入胶料;7.喂料时,进料口堵塞,严禁伸手到料口内抓料,也不得用棍棒往里捅,应提出胶料重新放入;8. 挤出开始后,人严禁站在机头正对方,防止机头未锁紧挤出时弹出;9. 严禁在运转中的辊筒上方传递物件,严禁在设备运转部位上依靠、跨越、站坐;10.调节机头螺栓时,注意观查周边是否有人,用力要适当,防止用力过度打滑摔倒或伤其他人;11.关机时,先关闭喷粉机,主机,然后再将胎筒全部收集完后关闭传送带;12.挤出机停机更换口型、芯型时,需两人协作,并防止上口型时落地伤脚或磕伤设备;13.停机启动时,主机要先开慢速,待主机完全运转后再开至规定转速,防止过快开启损伤设备;14.工作结束后,卸下机头,清空挤出机里面的余胶,清理废料,保持机器整洁,关闭水、电、风后搞好场地卫生。
0/5000
源语言: -
目标语言: -
结果 (简体中文) 1: [复制]
复制成功!
按照挤出机组的操作流程如下:<br>1.开机前,衣服穿着整齐,戴好劳保防护,禁止腰系绳带,严禁披衣、穿短裤、穿拖鞋上岗;<br>2.开机前,检查喂料口有无杂物,下班时喂料口需用盖板盖住,防止杂物落入挤出机内;<br>3.预热机头、机身、口型、芯型、清理标识线装置;预热带好防护用品,防止烫伤。预热达到工艺要求后关闭蒸气压力;<br>4.安装与规格相匹配的口型、芯型并锁紧,调整到规定的位置,保证胎筒的厚度均匀;<br>5.打开总电源,检查电气系统正常、操作控制系统灵敏可靠,开启油泵,检查油泵是否正常工作,润滑油是否流畅,听运转部位是否有异常声音;<br>6.启动主机,开启机头、机身、小辊筒、螺杆的全部冷却水,然后再送入胶料;<br>7.喂料时,进料口堵塞,严禁伸手到料口内抓料,也不得用棍棒往里捅,应提出胶料重新放入;<br>8. 挤出开始后,人严禁站在机头正对方,防止机头未锁紧挤出时弹出;<br>9. 严禁在运转中的辊筒上方传递物件,严禁在设备运转部位上依靠、跨越、站坐;<br>10.调节机头螺栓时,注意观查周边是否有人,用力要适当,防止用力过度打滑摔倒或伤其他人;<br>11.关机时,先关闭喷粉机,主机,然后再将胎筒全部收集完后关闭传送带;<br>12.挤出机停机更换口型、芯型时,需两人协作,并防止上口型时落地伤脚或磕伤设备;<br>13.停机启动时,主机要先开慢速,待主机完全运转后再开至规定转速,防止过快开启损伤设备;<br>14.工作结束后,卸下机头,清空挤出机里面的余胶,清理废料,保持机器整洁,关闭水、电、风后搞好场地卫生。
正在翻译中..
结果 (简体中文) 2:[复制]
复制成功!
按照挤出机组的操作流程如下:<br>1.开机前,衣服穿着整齐,戴好劳保防护,禁止腰系绳带,严禁披衣、穿短裤、穿拖鞋上岗;<br>2.开机前,检查喂料口有无杂物,下班时喂料口需用盖板盖住,防止杂物落入挤出机内;<br>3.预热机头、机身、口型、芯型、清理标识线装置;预热带好防护用品,防止烫伤。 预热达到工艺要求后关闭蒸气压力;<br>4.安装与规格相匹配的口型、芯型并锁紧,调整到规定的位置,保证胎筒的厚度均匀;<br>5.打开总电源,检查电气系统正常、操作控制系统灵敏可靠,开启油泵,检查油泵是否正常工作,润滑油是否流畅,听运转部位是否有异常声音;<br>6.启动主机,开启机头、机身、小辊筒、螺杆的全部冷却水,然后再送入胶料;<br>7.喂料时,进料口堵塞,严禁伸手到料口内抓料,也不得用棍棒往里捅,应提出胶料重新放入;<br>8. 挤出开始后,人严禁站在机头正对方,防止机头未锁紧挤出时弹出;<br>9. 严禁在运转中的辊筒上方传递物件,严禁在设备运转部位上依靠、跨越、站坐;<br>10.调节机头螺栓时,注意观查周边是否有人,用力要适当,防止用力过度打滑摔倒或伤其他人;<br>11.关机时,先关闭喷粉机,主机,然后再将胎筒全部收集完后关闭传送带;<br>12.挤出机停机更换口型、芯型时,需两人协作,并防止上口型时落地伤脚或磕伤设备;<br>13.停机启动时,主机要先开慢速,待主机完全运转后再开至规定转速,防止过快开启损伤设备;<br>14.工作结束后,卸下机头,清空挤出机里面的余胶,清理废料,保持机器整洁,关闭水、电、风后搞好场地卫生。
正在翻译中..
结果 (简体中文) 3:[复制]
复制成功!
According to the operation process of the extruder unit, it is as follows:<br>1. Before the machine is started, the clothes shall be dressed in order, and the labor protection shall be well worn. It is forbidden to tie the rope around the waist. It is forbidden to wear clothes, shorts and slippers to work;<br>2. Before starting the machine, check whether there are any sundries at the feeding port. The feeding port shall be covered with a cover plate to prevent sundries from falling into the extruder when off duty;<br>3. Preheat the head, body, mouth shape, core shape and clean the marking line device; preheat the protective equipment to prevent scalding. Close the steam pressure after preheating reaches the process requirements;<br>4. Install and lock the mouth type and core type matching the specification, adjust to the specified position, and ensure the uniform thickness of the tire barrel;<br>5. Turn on the main power supply, check whether the electrical system is normal, the operation control system is sensitive and reliable, turn on the oil pump, check whether the oil pump works normally, whether the lubricating oil is smooth, and listen to whether there is abnormal sound at the operation part;<br>6. Start the main engine, turn on all cooling water of the head, fuselage, small roller and screw, and then feed the rubber;<br>7. When feeding, the feed port is blocked. It is forbidden to reach into the feed port to grab the material, or poke it with a stick, and put the rubber material in again;<br>8. After extrusion, it is forbidden to stand at the opposite side of the head to prevent it from popping out when the head is not locked;<br>9. It is strictly prohibited to transfer objects above the running roller, and it is strictly prohibited to rely on, cross over or stand on the running parts of the equipment;<br>10. When adjusting the head bolt, pay attention to check whether there are people around, and use appropriate force to prevent excessive slipping and falling or hurting others;<br>11. When the machine is shut down, turn off the duster and the main engine first, and then turn off the conveyor belt after all the tubes are collected;<br>12. when the extruder is shut down to change the mouth type and core type, two people shall cooperate to prevent foot injury or equipment damage when the mouth type is applied;<br>13. When the machine is shut down and started, the main engine shall be started slowly first, and then it shall be started to the specified speed after the main engine is fully running, so as to prevent the equipment from being damaged due to too fast starting;<br>14. At the end of the work, remove the head, empty the remaining glue in the extruder, clean up the waste, keep the machine clean and tidy, and do a good job in site sanitation after turning off the water, electricity and wind.<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: