二次加密草捆时，将电控箱控制面板手动/自动循环旋钮旋至自动循环位置，横

When re-encrypting the bale, turn the manual/automatic circulation knob of the control panel of the electric control box to the automatic circulation position, the horizontal ejection hydraulic cylinder and the vertical ejection hydraulic cylinder are respectively returned to the original position, the hydraulic master cylinder is returned to the right end, and the forming mold The door opens automatically and the hydraulic pump is unloaded at this time. Put the bale after baling once into the left mold cavity, press the button of the automatic control master cylinder to move left, the left molding mold door will automatically close, the hydraulic pressure head of the master cylinder quickly moves to the left to suppress the bale, as the pressure increases, the main hydraulic pressure The moving speed of the cylinder slows down and finally reaches the required length of the bale, the main hydraulic cylinder stops moving, and the hydraulic pump unloads. At this time, the left cavity of the forming mold is manually bundled. At the same time, the right cavity of the forming mold also puts a bundle of bales after one-time baling. After the bundle of the left cavity of the forming mold is completed, press the automatic control master cylinder right shift button, The right side forming mold door closes automatically, the hydraulic main cylinder head quickly moves to the right to suppress the bale, and at the same time the left end of the hydraulic main cylinder retreats. As the pressure increases, the main hydraulic cylinder slows down and finally reaches the required length of the bale. The main hydraulic cylinder stops moving, and the large hydraulic pump is unloaded. The small hydraulic pump continues to work, automatically opens the left forming mold door, pushes the left cavity of the forming mold to push the horizontal ejection hydraulic cylinder to eject the bundled bale, and then pushes the longitudinal ejection hydraulic cylinder to eject the bale longitudinally, and manually remove the grass. The longitudinal ejection hydraulic cylinder returns to the original position, and the horizontal ejection hydraulic cylinder returns to the original position. The small hydraulic pump is unloaded, and then the mold cavity is put into a bale after a bale once again.

Secondary encryption of bales, the control panel manual /automatic cycle knob to the automatic cycle position, horizontal top hydraulic cylinder, vertical top hydraulic cylinder back to the original position, hydraulic master cylinder back to the right end, molding mold door automatically open, at this time the hydraulic pump discharge. Put the bales after a bale into the left end mold cavity, press the automatic control master cylinder left-move button, the left end mold door automatically closes, the hydraulic master cylinder pressure head quickly move to the left to suppress the bales, with the pressure increases the main hydraulic cylinder movement speed slows down, and finally reach the length required for the bale, the main hydraulic cylinder stops movement, the hydraulic pump unloading. At this time, the artificial mold left cavity bales are tied, while the molded right cavity is also placed in a bundle of grass bales after a bale, molded mold left cavity grass bales are bundled after completion, press the automatic control master cylinder right shift button, the right end mold door Automatic shut-off, hydraulic master cylinder head quickly move to the right to suppress the bale, while the hydraulic master cylinder left end pressure head back, with the pressure increases the main hydraulic cylinder movement speed slows down, and finally reached the required length of the bale, the main hydraulic cylinder stop movement, large hydraulic pump discharge. Small hydraulic pump continues to work, automatically open the left end molding mold door, promote the molding mold left cavity horizontal top hydraulic cylinder to tie up the grass bale top, and then push the vertical top hydraulic cylinder to the grass bale vertical top out, manually remove the grass bale, vertical top hydraulic cylinder back to the original position, horizontal top hydraulic cylinder also returned to the original position, small hydraulic pump discharge, and then the mold cavity into a bundle of grass bales.

When the bale is densified for the second time, turn the manual / automatic circulation knob on the control panel of the electric control box to the automatic circulation position, the horizontal ejection hydraulic cylinder and the longitudinal ejection hydraulic cylinder return to the original position respectively, the hydraulic master cylinder returns to the right end, and the forming mold door opens automatically. At this time, the hydraulic pump is unloaded. Put the baled bales into the left end mold cavity, press the left button of automatic control master cylinder, the left end molding mold door will close automatically, the hydraulic master cylinder pressure head will move quickly to the left to press bales, with the increase of pressure, the movement speed of the main hydraulic cylinder will slow down, and finally reach the required length of bales, the main hydraulic cylinder will stop moving, and the hydraulic pump will unload. At this time, the bales in the left cavity of the forming die are manually strapped, and at the same time, the bales in the right cavity of the forming die are also put into a bundle of bales after one-time baling. After the bales in the left cavity of the forming die are strapped, press the right button of the automatic control master cylinder, the forming die door at the right end is automatically closed, the hydraulic master cylinder pressure head quickly moves to the right to press the bales, and the hydraulic master cylinder pressure head at the left end returns, With the increase of pressure, the moving speed of the main hydraulic cylinder slows down, and finally reaches the required length of the bale, the main hydraulic cylinder stops moving, and the large hydraulic pump unloads. The small hydraulic pump continues to work, automatically opens the door of the left end forming die, pushes the transverse ejection hydraulic cylinder in the left cavity of the forming die to eject the bundled bales, and then pushes the longitudinal ejection hydraulic cylinder to eject the bales longitudinally, manually takes out the bales, the longitudinal ejection hydraulic cylinder returns to its original position, and the transverse ejection hydraulic cylinder also returns to its original position, and the small hydraulic pump unloads, After that, a bale of baled grass is put into the mold cavity.<br>