LOW PRESSURE NITROGEN TO D130 The f

LOW PRESSURE NITROGEN TO D130 The flow of low pressure nitrogen to the vent line of D130 is controlled by FIC-________. This is a local rotameter with a flow range of 0 to 0.2 kg/hr. The flow of this nitrogen keeps an inert atmosphere in the tank. GREASE CHARGE TO D130 Grease is charged from drums using P130. Usually, complete drums are charged to avoid contamination.GREASE CHARGE TO THE CATALYST DISPERSION DRUMS D140A/B. Flow totalizer FTS-________ is set by field operator for the number of liters to be charged to the dispersion drum. The number of liters charged will be determined by the desired catalyst concentration. HS-_______ starts the flow. When the switch is activated, the valve on D130 circulating line closes and the valve on the D140 A/B addition line opens. When the grease addition is complete, the valve on D130 circulation line opens and the valve on the addition line closes. The valve on D130 circulation line (FV-________) will air fail open and the valve on the addition line will air fail close (FV-_______). Instrument range is 0-1000 kg.The temperature in D130 is controlled by temperature indicator/controller TICA-________. This device has a range of 0C to 150C and a setpoint of 90 C. High alarm set point is 1200 C. Low alarm set point is 700C. TICA-________ regulates the steam supply to the grease drum jacket and recirculation line, by reading the grease temperature in the drum. The temperature of the grease in the circulation line from P130 to D130 is indicated by TIA-______. This is a board mounted instrument with a high temperature alarm set at 120 C.EA-_______ Indicates motor stop on P130. The alarm is located on the control room console.CATALYST DISPERSION & FEEDING SYSTEMS (PIDs14A,14B,15)CATALYST DISPERSION DRUMS D140A/B The drums are jacketed vessels equipped with agitators. In the drum, powdered Catalyst is blended into the oil/grease mixture. The capacity of each vessel is _______ m3. Operating temperature range is 5 to 70 0C.

LOW PRESSURE NITROGEN TO D130 The flow of low pressure nitrogen to the vent line of D130 is controlled by FIC-________. This is a local rotameter with a flow range of 0 to 0.2 kg/hr. The flow of this nitrogen keeps an inert atmosphere in the tank. GREASE CHARGE TO D130 Grease is charged from drums using P130. Usually, complete drums are charged to avoid contamination.GREASE CHARGE TO THE CATALYST DISPERSION DRUMS D140A/B. Flow totalizer FTS-________ is set by field operator for the number of liters to be charged to the dispersion drum. The number of liters charged will be determined by the desired catalyst concentration. HS-_______ starts the flow. When the switch is activated, the valve on D130 circulating line closes and the valve on the D140 A/B addition line opens. When the grease addition is complete, the valve on D130 circulation line opens and the valve on the addition line closes. The valve on D130 circulation line (FV-________) will air fail open and the valve on the addition line will air fail close (FV-_______). Instrument range is 0-1000 kg.The temperature in D130 is controlled by temperature indicator/controller TICA-________. This device has a range of 0C to 150C and a setpoint of 90 C. High alarm set point is 1200 C. Low alarm set point is 700C. TICA-________ regulates the steam supply to the grease drum jacket and recirculation line, by reading the grease temperature in the drum.  The temperature of the grease in the circulation line from P130 to D130 is indicated by TIA-______. This is a board mounted instrument with a high temperature alarm set at 120 C.EA-_______ Indicates motor stop on P130. The alarm is located on the control room console.CATALYST DISPERSION & FEEDING SYSTEMS (PIDs14A,14B,15)CATALYST DISPERSION DRUMS D140A/B  The drums are jacketed vessels equipped with agitators. In the drum, powdered Catalyst is blended into the oil/grease mixture. The capacity of each vessel is _______ m3. Operating temperature range is 5 to 70 0C.

0/5000

源语言: -

目标语言: -

结果 (简体中文) 1: [复制]

复制成功！

低压氮TO D130 低压氮气流至D130的通风线通过FIC控制-________。这是一个本地转子流量计为0的流量范围来???0.2千克/小时。此氮气流保持在惰性气氛中的罐中。 润滑脂充电到D130 润滑脂使用P130鼓充电。通常，完整的鼓充电，以避免污染。 GREASE充电到催化剂分散DRUMS D140A / B。 流量积算FTS -________由现场操作员对将被充电到分散体鼓升数设置。带电升的数量将通过所需的催化剂浓度来确定。HS -_______开始流动。当开关被激活时，打开上D130循环管线关闭阀和阀的D140 A / B添加管线。当油脂添加完成后，在D130循环管路阀门打开，上相加行关闭阀门。在D130循环线（FV -________）阀门将空气无法打开和添加管线阀门将空气无法关闭（FV -_______）。仪器范围是0-1000公斤。 在D130的温度由温度指示器/控制器TICA -________控制。该装置具有到150℃的范围0℃和90℃高警报设定点的设定点是1200℃低报警设定点70℃。TICA -________调节蒸汽供应到油脂鼓护套和再循环管线，通过在滚筒中读取润滑脂温度。 在从P130到D130循环管路润滑脂的温度由TIA指示-______。这是一个板，安装仪器用高温报警设定在120℃ EA -_______指示上P130电机停止。该警报是位于中控室控制台上。 催化剂分散体和供料系统（PIDs14A，14B，15） 催化剂分散DRUMS D140A / B 辊筒套配有搅拌器的船只。在滚筒，粉末状催化剂被 混合到油/油脂混合物。每个容器的容量为_______立方米。的工作温度范围为5〜70 0℃。

正在翻译中..

结果 (简体中文) 2:[复制]

复制成功！

低压氮到 D130 低压氮气流向 D130 通风管管的流量由 FIC-__控制。这是一个流量范围为 0 到 0.2 kg/hr 的本地旋转计。这种氮气的流动使水箱中保持惰性大气。 润滑脂充电到 D130 使用 P130 从鼓中充电润滑脂。通常，为避免污染而对完整的鼓进行充电。 润滑电达到催化剂分散鼓 D140A/B。 流量总化器 FTS-* 由现场操作员设置，用于向分散鼓充电的升数。充电的升数将由所需的催化剂浓度决定。HS_* 启动流。当开关激活时，D130 循环管路上的阀关闭，D140 A/B 加线上的阀打开。润滑脂添加完成后，D130 循环管路上的阀打开，加法管路上的阀关闭。D130 循环管路（FV-*）上的阀将空气失效打开，加法管路上的阀将空气关闭（FV-_）。。仪器范围为 0-1000 kg。 D130 中的温度由温度指示器/控制器 TICA-__控制。本装置范围为0C至150C，设定点为90C。高报警设定点为1200 C，低报警设定点为700C。TICA-* 通过读取滚筒中的润滑脂温度，调节润滑脂桶护套和再循环线的蒸汽供应。 从 P130 到 D130 的循环管线中的润滑脂温度由 TIA-*指示。这是一个板式安装仪器，温度报警设置为 120 C。 EA-* 表示 P130 上的电机停止。报警位于控制台上。 催化系统 + 馈送系统（PIDs14A，14B，15） 催化剂分散鼓 D140A/B 鼓是装有搅拌器的护套容器。在鼓中，粉末催化剂是 混合到油/油脂混合物中。每艘船的容量为+m3。工作温度范围为 5 至 70 0C。

正在翻译中..

结果 (简体中文) 3:[复制]

复制成功！

低压氮气至D130 到D130排气管的低压氮气流量由FIC-控制。这是一个局部浮子流量计，流量范围为0至0.2 kg/hr。氮气的流动使罐内保持惰性气体。 润滑脂加注至D130 使用P130从桶中加注润滑脂。通常情况下，为了避免污染，整个桶都要加料。 向催化剂分散罐D140A/B加注润滑脂。 流量积算器FTS-}}}}}}}}}}}}}}}}}}}}}。充电的升数将由所需的催化剂浓度决定。HS-uuuuuuuuuuuuuuuu开始流动。当开关启动时，D130循环管线上的阀门关闭，D140 A/B添加管线上的阀门打开。润滑脂添加完成后，D130循环管路上的阀门打开，添加管路上的阀门关闭。D130循环管线上的阀门（FV-}}}}}}}}}}}}}}}}}}}}}}}}}）将空气。仪器量程为0-1000 kg。 D130的温度由温度指示器/控制器TICA-控制。该装置的温度范围为0C至150C，设定值为90 C。高报警设定值为1200 C。低报警设定值为700 C。TICA-庘庘庘庘庘庘庘庘庘庘庘庘庘庘庘。 从P130到D130的循环管路中的润滑脂温度由TIA-指示。这是一个安装在板上的仪器，高温警报设置在120摄氏度。 EA-uuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu表示P130上的电机停止。报警器位于控制室控制台上。 催化剂分散和进料系统（PIDs14A、14B、15） 催化剂分散罐D140A/B 桶是装有搅拌器的夹套容器。在鼓里，粉末状催化剂是 混合到油/脂混合物中。每个容器的容量为立方米。工作温度范围为5到70摄氏度。

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.