(4) The elevation belt template is

(4) The elevation belt template is installed according to the size requirements to ensure that the base width and elevation are accurate. The top surface of the template should be flush with the design elevation. The maximum error requirement should be controlled within 2mm. The template should be stable, straight, flat, without distortion, and phase. Adjacent formwork connection is tight and smooth, no bottom leakage, front and rear staggering, and high and low staggering are prohibited. It is strictly forbidden to dig grooves on the base layer and embed the installation formwork. The formwork is welded to ensure smoothness between adjacent forms The lateral supports are added to support the foot of the side wall of the tunnel, and the additional spacing is generally 1 to 2m;(5) The gap between the formwork and the formwork should be filled with mortar to prevent slurry leakage.

0/5000

源语言: -

目标语言: -

结果 (简体中文) 1: [复制]

复制成功！

（4）按照尺寸要求安装升降带模板，以确保底座宽度和高度正确。模板的上表面应与设计标高齐平。最大误差要求应控制在2mm以内。模板应稳定，笔直，平坦，无扭曲和相位。相邻的模板连接紧密且平滑，禁止底部漏水，前后交错以及上下交错。严禁在基层上挖槽并嵌入安装模板。焊接模板以确保相邻模板之间的平滑度。添加侧向支撑以支撑隧道侧壁的底部，附加间距通常为1至2m；<br>（5）模板与模板之间的缝隙应填满砂浆，以防止浆液泄漏。

正在翻译中..

结果 (简体中文) 2:[复制]

复制成功！

(4) The elevation belt template is installed according to the size requirements to ensure that the base width and elevation are accurate. The top surface of the template should be flush with the design elevation. The maximum error requirement should be controlled within 2mm. The template should be stable, straight, flat, without distortion, and phase. Adjacent formwork connection is tight and smooth, no bottom leakage, front and rear staggering, and high and low staggering are prohibited. It is strictly forbidden to dig grooves on the base layer and embed the installation formwork. The formwork is welded to ensure smoothness between adjacent forms The lateral supports are added to support the foot of the side wall of the tunnel, and the additional spacing is generally 1 to 2m;<br>(5) The gap between the formwork and the formwork should be filled with mortar to prevent slurry leakage.

正在翻译中..

结果 (简体中文) 3:[复制]

复制成功！

（4）根据尺寸要求安装标高带模板，保证基础宽度和标高准确。模板顶面应与设计标高平齐。最大误差要求控制在2毫米以内。模板应稳定、直、平、无变形、相位。相邻模板连接严密、平整，无漏底、前后错开、高低错开现象。严禁在基层上开槽、预埋安装模板。模板采用焊接保证相邻模板间的平整度，隧道边墙底部增设侧向支撑，附加间距一般为1～2m；<br>（5）模板与模板之间的缝隙应用砂浆填实，防止漏浆。<br>

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.