冷却水孔中心线与型腔壁之间的距离应为冷却水道直径的1至2倍(通常为12mm至15mm),并且冷却水通道之间的中心距离约为水孔直径的3至5倍。的英语翻译

冷却水孔中心线与型腔壁之间的距离应为冷却水道直径的1至2倍(通常为12

冷却水孔中心线与型腔壁之间的距离应为冷却水道直径的1至2倍(通常为12mm至15mm),并且冷却水通道之间的中心距离约为水孔直径的3至5倍。水通道的直径通常超过8毫米。从冷却水孔到型腔表面的距离应尽可能相等。如果塑件壁厚均匀,则冷却水孔和型腔表面之间的任何距离应尽可能相等,如果塑件壁厚不均匀时,则应增加冷却效果。浇口处要加强冷却。冷却水通道不应穿过镶块或其连接部位,以防至有水溢出。应避免在塑件接痕处设计冷却水孔。进出水口水管接头的位置应尽可能位于模具的同一侧,通常设在注塑机的背面。在模具上打开冷却水道,循环水立即对模具进行冷却,
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
The distance between the center line of the cooling water hole and the cavity wall should be 1 to 2 times the diameter of the cooling water channel (typically 12mm to 15mm), and the center distance between the cooling water channels is about 3 to 5 times the diameter of the water hole . The diameter of the water channel usually exceeds 8 mm. The distance from the cooling water hole to the cavity surface should be as equal as possible. If the wall thickness of the plastic part is uniform, any distance between the cooling water holes and the surface of the cavity should be as equal as possible. If the wall thickness of the plastic part is uneven, the cooling effect should be increased. Strengthen cooling at the gate. <br>The cooling water channel should not pass through the insert or its connection to prevent water overflow. <br>Avoid designing cooling water holes at the joints of plastic parts. The position of the water inlet and outlet pipe joints should be located on the same side of the mold as possible, usually on the back of the injection molding machine. Open the cooling water channel on the mold, and the circulating water immediately cools the mold.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
The distance between the center line of the cooling water hole and the cavity wall shall be 1 to 2 times the diameter of the cooling watercourse (usually 12mm to 15mm) and the center distance between the cooling water passages shall be approximately 3 to 5 times the diameter of the water hole. Water passages usually have diameters of more than 8 mm. The distance from the cooling water hole to the surface of the cavity should be as equal as possible. If the wall thickness of the plastic piece is uniform, any distance between the cooling water hole and the cavity surface should be as equal as possible, and if the wall thickness of the plastic part is uneven, the cooling effect should be increased. The gate should be cooled.<br>Cooling water passages should not pass through the panels or their connections to prevent water spillage.<br>Cooling water holes should be avoided at the seams of the plastic parts. The position of the water outlet connection in and out should be located on the same side of the mold as far as possible, usually on the back of the injection moulding machine. Open the cooling watercourse on the mold and the circulating water immediately cools the mold.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
The distance between the center line of the cooling water hole and the cavity wall shall be 1 to 2 times the diameter of the cooling water channel (usually 12mm to 15mm), and the center distance between the cooling water channels shall be about 3 to 5 times the diameter of the water hole. The diameter of the water passage is usually more than 8 mm. The distance from the cooling water hole to the surface of the cavity should be as equal as possible. If the wall thickness of the plastic part is uniform, any distance between the cooling water hole and the surface of the cavity shall be equal as much as possible. If the wall thickness of the plastic part is uneven, the cooling effect shall be increased. Strengthen cooling at the gate.<br>The cooling water channel shall not pass through the insert or its connection part to prevent water overflow.<br>The design of cooling water holes at plastic joint marks shall be avoided. The position of the water inlet and outlet pipe joint shall be on the same side of the mold as much as possible, usually on the back of the injection molding machine. Open the cooling water channel on the mold, and the circulating water immediately cools the mold,<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: