Sensor with flat, flexible probe (l=300 mm, w=10 mm, d=1.5 mm) for moi的简体中文翻译

Sensor with flat, flexible probe (l

Sensor with flat, flexible probe (l=300 mm, w=10 mm, d=1.5 mm) for moisture tests under car floor coverings. Support material: glass fibre-reinforced epoxy resin / conductor paths: copper, nickel plated Active measuring area: 50x10 mm on both sides Operation For a longer storage or transportation the moisture probe has to be switched off to avoid a deep discharge of the accumulator (devices are delivered switched-off). Before storage full load the devices because the accumulator can be damaged by discharging itself (minimum charge once a year. The device doesn’t need to be switched on for charging). The entry of the switch is closed with a hexagon socket headless screw. Unscrew it. Use a little slot screwdriver (3mm blade) to operate the miniature-rotary switch carefully (approx. 45° left or right). The switch has 3 positions (see picture). In the mid-position (2) the device is switched off. For additional information watch the video clip on our homepage. Attention ! Screw in the hexagon headless screw only as deep as necessary ! If you screw it in to deep the switch and the electronic circuit can be damaged ! Suitable screw drivers are part of the delivery for new devices. To activate the electronic, after switching on, a charging has to take effect. For this, connect the moisture probe by the charging socket with the international usable charger. The charging control LED glows yellow (3 colour LED) while charging. Charging time: max. 10 hours (complete charge process). The electronic switch-off automatic when the accumulator is fully charged and the control LED glows green. After this, the device is ready for use. A functional test can be done by bridging the electrodes with wet fingers. If the charging control LED glows red, the device has to be charged. If desired the holder can be mount somewhere by a hole in the bottom. The 2-pin electrodes and all the other probes are equipped with plug connection, so they can be changed without any problem after wearout. Therefore loose the electrode screwing (hexagon nut) and change the electrodes. For fixing the electrodes, screw on the electrodes again.
0/5000
源语言: -
目标语言: -
结果 (简体中文) 1: [复制]
复制成功!
带有扁平柔性探头(l = 300毫米,w = 10毫米,d = 1.5毫米)的传感器,用于在汽车地板下进行湿度测试。支撑材料:玻璃纤维增​​强环氧树脂/导体路径:铜,镀镍有效测量面积:两侧均为50x10 mm操作要长期存放或运输,必须关闭湿度探头,以避免蓄能器深度放电(设备出厂时已关闭)。在满载存储之前,设备会因为蓄能器自身放电而损坏(每年最少充电一次。不需要打开设备进行充电)。开关的入口用六角头无头螺钉封闭。拧开它。使用小号一字螺丝刀(3毫米刀片)小心操作微型旋转开关(左右倾斜45°)。开关有3个位置(见图)。在中间位置(2),设备关闭。有关更多信息,请观看我们主页上的视频片段。注意!仅拧入所需深度的六角无头螺钉!如果将其拧入到较深的位置,开关可能会损坏电子电路!合适的螺丝刀是新设备交付的一部分。为了激活电子设备,在打开电源后必须进行充电。为此,请通过充电插座将水分探头与国际可用的充电器连接。充电时,充电控制LED呈黄色发光(3色LED)。充电时间:最长 10小时(完整的充电过程)。当蓄电池充满电并且控制LED呈绿色亮起时,电子自动关闭。此后,该设备即可使用。通过用湿手指桥接电极可以完成功能测试。如果充电控制LED呈红色亮起,则必须为设备充电。如果需要,可以通过底部的孔将支架固定在某处。2针电极和所有其他探针均配有插头连接,因此磨损后可以无问题地进行更换。因此,松开电极的螺钉(六角螺母)并更换电极。要固定电极,请再次拧紧电极。
正在翻译中..
结果 (简体中文) 2:[复制]
复制成功!
带扁平、柔性探头的传感器(l=300 mm,w=10 mm,d=1.5 mm),用于在汽车地板覆盖物下进行水分测试。支撑材料:玻璃纤维增强环氧树脂/导体路径:铜、镀镍有源测量区域:两侧50x10mm操作对于较长的存储或运输,必须关闭水分探针以避免蓄能器的深度放电(设备已关闭)。在存储满载设备之前,由于蓄能器本身可能损坏(每年最低充电一次)。无需打开设备充电)。开关的入口用六角插座无头螺钉关闭。拧开。使用小插槽螺丝刀(3mm 刀片)小心操作微型旋转开关(左右 45° 左右)。开关有 3 个位置(见图)。在中间位置 (2) 中,设备已关闭。有关更多信息,请观看我们主页上的视频剪辑。注意!六角无头螺钉中只有必要的深度!如果你拧入深开关和电子电路可能会损坏!合适的螺丝刀是新设备交付的一部分。要激活电子装置,打开后,充电必须生效。为此,通过充电插座将水分探头与国际可用充电器连接。充电控制指示灯在充电时呈黄色(3 色 LED)。充电时间:最多 10 小时(完整充电过程)。当蓄能器充满电且控制 LED 指示灯呈绿色亮起时,电子关闭自动关闭。在此之后,设备即可使用。可以通过用湿手指桥接电极进行功能测试。如果充电控制指示灯呈红色亮起,则必须为设备充电。如果需要,支架可以通过底部的孔安装在某处。双针电极和所有其他探头都配有插头连接,因此在磨损后可以毫无问题地更换。因此松开电极拧紧(六角螺母)并更换电极。要固定电极,请再次拧紧电极。
正在翻译中..
结果 (简体中文) 3:[复制]
复制成功!
Sensor with flat, flexible probe (l=300 mm, w=10 mm, d=1.5 mm) for moisture tests under car floor coverings. Support material: glass fibre-reinforced epoxy resin / conductor paths: copper, nickel plated Active measuring area: 50x10 mm on both sides Operation For a longer storage or transportation the moisture probe has to be switched off to avoid a deep discharge of the accumulator (devices are delivered switched-off). Before storage full load the devices because the accumulator can be damaged by discharging itself (minimum charge once a year. The device doesn’t need to be switched on for charging). The entry of the switch is closed with a hexagon socket headless screw. Unscrew it. Use a little slot screwdriver (3mm blade) to operate the miniature-rotary switch carefully (approx. 45° left or right). The switch has 3 positions (see picture). In the mid-position (2) the device is switched off. For additional information watch the video clip on our homepage. Attention ! Screw in the hexagon headless screw only as deep as necessary ! If you screw it in to deep the switch and the electronic circuit can be damaged ! Suitable screw drivers are part of the delivery for new devices. To activate the electronic, after switching on, a charging has to take effect. For this, connect the moisture probe by the charging socket with the international usable charger. The charging control LED glows yellow (3 colour LED) while charging. Charging time: max. 10 hours (complete charge process). The electronic switch-off automatic when the accumulator is fully charged and the control LED glows green. After this, the device is ready for use. A functional test can be done by bridging the electrodes with wet fingers. If the charging control LED glows red, the device has to be charged. If desired the holder can be mount somewhere by a hole in the bottom. The 2-pin electrodes and all the other probes are equipped with plug connection, so they can be changed without any problem after wearout. Therefore loose the electrode screwing (hexagon nut) and change the electrodes. For fixing the electrodes, screw on the electrodes again.<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: