质量、外检拉动物流包装科对零部件器具进行排查。主要针对生产过程磕碰、划

The Quality and External Inspection pulls the Animal Flow Packaging Division to conduct inspections on parts and appliances. Mainly for bumps and scratches in the production process. After <br>receiving the 20 sets of rear combination lights provided by the External Inspection Department, the supplier’s on-site service personnel are encouraged to confirm the problem of the parts causing the lights to not turn on, and replace the fault lights. <br>"1 implementation of quality interior doors Why two different team record, whether similar problems can be unified recording mode. <br>2, the interior door found that 100% quality problems after pulling the external examination to confirm, leaving the car analysis, if necessary. " <br>moved to the quiet before the inspection project quality inspection door <br>to problems into the torque control, a minimum of 10 lines each class every day, evenly distributed. <br>"1. The OM457 model accepts the current situation when the oil dipstick is not obstructed. <br>2. The solution that requires the assistance of both hands when the oil dipstick is inserted is adopted. <br>3. The final inspection adjusts the inspection standards for the above two points." For <br>the side marker lamp/side The turn signal does not light up, and it requires 100% to pull the external inspection department to confirm and replace the fault light. <br>It is required to provide the last 20 sets of rear combination lights, and the supplier’s on-site service personnel will confirm the problem during the final inspection. <br>Detect the dismantling of the air-conditioning filler port for the failed car. Inspect <br>the failed parts provided by the final assembly for the air leakage problem. <br>Compare and test the glass guide rails of the two suppliers. Clarify the standard operation document requirements and control the area to refine the assembly process of the production line, and issue the OK standard for the problem points. Improve the conclusion before August 28<br><br><br><br>

Quality, external inspection pull logistics packaging section of the parts and components of the appliances for inspection. Mainly for the production process bump, scratch problem parts.<br>After receiving 20 sets of rear combined lights provided by the External Inspection Section, the problem of the components causing the lights not to turn on pulls the supplier field service personnel to confirm and replace the faulty lights.<br>"1, the implementation of the interior quality door why the two teams record different, similar issues can be unified recording mode.<br>2, interior quality door found the problem after 100% pull external inspection to confirm, if necessary, stay car analysis. "<br>The inspection item is moved forward to the static quality gate.<br>The problem points are incorporated into torque control, with an average distribution of at least 10 lines per shift per day.<br>"1, OM457 models in the oil gauge is not blocked to receive the status quo.<br>2, the adoption of the oil ruler insertion need to use both hands to assist the program.<br>3, the final inspection for the above two points to adjust the inspection standards. "<br>For the side beacon/side steering light is not on, 100% pull the external inspection section to confirm, and replace the faulty lamp.<br>The last 20 sets of rear combined lights are required, and the problem is confirmed by the supplier field service personnel at the final inspection.<br>Testing for the removal of air conditioning filling port for failed vehicles.<br>In view of the air leakage problem, the failure parts provided by the assembly are tested.<br>Compare the guides on glass for both suppliers.<br>For the failure of the car pull inspection will be air conditioning filling port removal for testing.<br>Identify standard operating documentation requirements and control areas.<br>Refine the assembly process of the production line and issue OK standards for problem points.<br>Improvement conclusions are required by 28 August.

Quality and external inspection pull the logistics packaging department to check the parts and tools. It mainly aims at the parts with bumps and scratches in the production process<br>After receiving 20 sets of rear combination lamps provided by the external inspection department, the supplier's on-site service personnel were pulled to confirm the problem of light failure caused by parts and components, and replace the fault light<br>"1. Why are the records of interior quality door different between the two teams, and whether the record mode of similar problems can be unified.<br>2. When problems are found in the interior quality door, pull the external inspection 100% for confirmation, and leave the vehicle for analysis if necessary. "<br>Inspection items moved forward to static inspection quality gate<br>The problem points are included in the torque control, and each shift line has at least 10 sets per day, with average distribution.<br>"1. Om457 models receive the status quo without the oil dipstick blocked.<br>2. Adopt the scheme of using both hands to assist when inserting the oil dipstick.<br>3. The final inspection adjusts the inspection standard according to the above two points. "<br>In view of the problem that the side marker lamp / side steering light is not on, it is required to pull the external inspection department 100% to confirm and replace the fault lamp.<br>After 20 sets of rear combination lamps are required to be provided, and the supplier's on-site service personnel shall confirm the problems in the final inspection.<br>In view of the failure of the car, the air conditioning filler is removed for detection<br>Aiming at the problem of air leakage, the failure parts provided by the general assembly were detected<br>The glass guide rails of two suppliers were compared and tested<br>In view of the failure vehicle pulling external inspection, the air conditioning filler was removed for detection<br>Define the standard operation document requirements and control area<br>Refine the assembly process of the production line and issue the OK standard for the problem points<br>It is required to make improvement conclusion before August 28<br>