安装墙柱铝模前，根据标高控制点检查墙柱位置楼板标高是否符合要求，高出的

Before installing the wall pillar aluminum mold, check whether the height of the floor slab at the position of the wall pillar meets the requirements according to the elevation control point. The higher chisel is removed, and the lower wedge is placed on the wooden wedge. Try to control it within 5mm. <br>②Welding the positioning steel bar on the root of the wall column and the longitudinal bar at the top to prevent the column aluminum mold from running during the reinforcement; set the cement internal brace or steel bar internal brace with the same thickness as the wall column to ensure the aluminum mold The cross-sectional dimensions of the wall post after reinforcement. <br>③Before assembling the aluminum molds of the wall columns, the board surface must be cleaned up completely, and the mold release agent must be applied. The release agent should be applied thinly and evenly without brushing. <br>④Assemble the wall post aluminum mold in sequence according to the test assembly drawing number. Before closing the column aluminum mold, it is necessary to pre-coat the PVC pipe on the wall post mold fastening screw, and at the same time, ensure that the contact position of the casing and the template surface on both sides of the wall must be accurate, so that After pouring, the pull screw can be retracted. <br>⑤When installing the opening template, set the door and window opening template according to the engineering requirements, and the four sides of the opening are firmly connected to the wall template. <br>⑥In order to facilitate the removal, the head of the pin should be as far as possible inside the inner corner mold when the wall pillar mold is connected with the inner corner mold. <br>The iron piece on the connecting pin between the aluminum molds of the wall columns should be inserted from top to bottom to avoid falling off when the concrete is poured. <br>3) Beam formwork support: When installing the beam formwork, first install the formwork at the bottom of the beam. One side of the bottom formwork is erected on the supported column formwork or wallboard

Before installing the wall column aluminum mold, according to the height control point to check the wall column position floor height is in line with the requirements, high chisel removal, low mat on the wooden wedge, as far as possible to control within 5mm.<br>(2) Weld ingestthes the positioning of the steel bar on the root and top of the wall column, prevent the column aluminum mold from running in the reinforcement, and set up the cement inner support or steel bar with the thickness of the wall column in the wall column to ensure the cross-sectional dimensionofs of the aluminum mold in the reinforced rear wall column.<br>(3) Before the wall column aluminum mold is assembled, the surface must be thoroughly cleaned, painted mold-removal agent. The release agent brush should be thin and uniform, do not leak the brush.<br>(4) According to the test assembly drawing number in turn to assemble the wall column aluminum mold, closed column aluminum mold, need to be in the wall column mold fastening screw pre-coatPVC tube, at the same time to ensure that the casing and the two sides of the wall template surface contact position to be accurate, in order to pour back the pull screw.<br>(5) When installing the hole port template, according to the engineering requirements to set the door and window hole template, the four sides of the hole and the wall template connection is secure.<br>(6) In order to remove the convenient, the wall column mold and the inner angle mold when connected when the head of the pin should be as far as possible inside the inner angle mold.<br>The iron sheet on the connecting pin between the aluminum molds of the wall pillars should be inserted from top to bottom to avoid falling off when the concrete is poured.<br>3) Beam template branch: when installing beam template, first install the beam bottom template, the bottom of the mold side is set on the already supported column mold or wall board ...

Before installing the aluminum formwork of wall column, check whether the floor elevation at the position of wall column meets the requirements according to the elevation control point, Chisel out the higher part, and put the wooden wedge on the lower part, and try to control it within 5mm.<br>② The positioning steel bars shall be welded on the longitudinal bars at the root and top of the wall column to prevent the column aluminum form from moving when strengthening; the cement internal bracing or steel internal bracing with the same thickness of the wall column shall be set in the wall column to ensure the section size of the wall column after the aluminum form is strengthened.<br>③ Before the assembly of wall column aluminum mold, the board surface must be completely cleaned and coated with release agent. The release agent shall be applied thinly and evenly without missing.<br>④ Assemble the wall column aluminum mold according to the number of trial assembly drawing. Before closing the column aluminum mold, coat PVC pipe on the fastening screw of the wall column mold in advance. At the same time, ensure that the contact position between the sleeve and the formwork surface on both sides of the wall is accurate, so that the pull screw can be recovered after pouring.<br>⑤ When installing the opening formwork, the door and window opening formwork shall be set according to the engineering requirements, and the four sides of the opening shall be firmly connected with the wall formwork.<br>⑥ In order to facilitate the removal, the head of the pin shall be in the internal corner mold as much as possible when the wall column mold is connected with the internal corner mold.<br>The iron sheet on the connecting pin between the aluminum forms of the wall column shall be inserted from top to bottom to avoid falling off during the concrete pouring.<br>3) Beam formwork erection: when installing beam formwork, first install the formwork at the beam bottom, and one side of the bottom formwork shall be erected on the erected column formwork or wall panel