将固定片内层加热数秒钟使乳白胶层发亮。沿轴向对折定位于收缩带接缝处的胶

将固定片内层加热数秒钟使乳白胶层发亮。沿轴向对折定位于收缩带接缝处的胶条,然后掀起固定片的一边,用火加热固定片的内层，使乳白胶层发亮变软,然后迅速压紧压实。再用同样的方法安装另一边,最后将固定片上方往返加热数次辊压，一定要粘接牢固,网格清晰可见。注：固定片一定要一次性安装好(也可在安装完成后用底漆涂在固定片边上)

0/5000

源语言: -

目标语言: -

结果 (英语) 1: [复制]

复制成功！

Heat the inner layer of the fixing sheet for a few seconds to make the milky white glue layer shiny. Fold the rubber strip positioned at the seam of the shrink belt in the axial direction, then lift one side of the fixed sheet, heat the inner layer of the fixed sheet with fire to make the milky white glue layer bright and soft, and then quickly compact and compact. Then use the same method to install the other side, and finally heat the top of the fixed piece back and forth for several times, and it must be firmly bonded and the grid clearly visible. Note: The fixing piece must be installed at one time (it can also be painted on the edge of the fixing piece with primer after installation)

正在翻译中..

结果 (英语) 2:[复制]

复制成功！

Heat the inner layer of the fixing sheet for a few seconds to brighten the latex layer. Along the axial folding strip located at the seam of the shrink belt, and then set off the side of the fixing sheet, heating the inner layer of the fixing sheet with fire, so that the latex layer brightens and softens, and then quickly compacts the compaction. Then use the same method to install the other side, and finally the fixed piece above the round-trip heating several roller pressure, must be bonded firmly, the mesh is clearly visible. Note: The fixing plate must be installed at once (it is also possible to apply primer to the edge of the fixing plate after installation)

正在翻译中..

结果 (英语) 3:[复制]

复制成功！

Heat the inner layer of the fixator for several seconds to make the opal layer shine. Fold the adhesive strip at the joint of the contraction belt along the axial direction, lift up one side of the fixed piece, heat the inner layer of the fixed piece with fire to make the milky white adhesive layer bright and soft, and then press and compact it quickly. Use the same method to install the other side, and finally heat and roll the upper part of the fixed plate for several times. Make sure that the bonding is firm and the grid is clear and visible. Note: the fixing piece must be installed at one time (primer can also be applied on the edge of the fixing piece after installation)<br>

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.