1、当轴承运行到一定时期时(或保维护养期),将轴承全部撤下;2、用清洗用的柴油或煤油浸泡清洗轴承,如有技术条件最好打开密封盖清洗;3、清洗后的英语翻译

1、当轴承运行到一定时期时(或保维护养期),将轴承全部撤下;2、用清洗

1、当轴承运行到一定时期时(或保维护养期),将轴承全部撤下;2、用清洗用的柴油或煤油浸泡清洗轴承,如有技术条件最好打开密封盖清洗;3、清洗后空干清洗油,外观检查有无损伤;4、用一个150mm左右,直径为角接触球轴承内径相等的木棒(最好为空心管),一端固定一个轴承;5、用手快速转动轴承的同时,将木棒(木管)另一端顶在耳朵上或音频放大器话筒上辩听轴承转动噪音;6、固定轴承后横向拨动木棒,检查轴承是否磨损松动现象;7、松动严重、转动噪音过大、有严重缺损的FAG轴承应以淘汰,以同型号代之;8、取一桶将适量润滑脂(优质黄干油)用文火融化(不可过热),将检测过的轴承放入桶中浸泡到无气泡溢出。润滑脂冷却前取出轴承,残留润滑脂量少。润滑脂冷却后取出角接触球轴承,残留润滑脂量多。根据需要确定润滑脂残留量的多少。9、用软布或卫生纸擦净轴承外面的润滑脂将FAG轴承安原状装配到滑轮上,保养维护工作即告结束。
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
1, when the operation of the bearing to a certain period (or raised maintenance of security), removed all of the bearing; <br>2, washed with kerosene or diesel immersion cleaning bearings, if conditions are preferably sealed cover wash technology; <br>3, cleaning after air drying oil cleaning, appearance inspection for damage; <br>4, with about a 150mm, a diameter equal to the inner diameter of the stick angular contact ball bearings (preferably a hollow tube), one end of a fixed bearing; <br>5, rapid rotation of the hand bearing while the stick (woodwind) on top of the other end of the ear or listening to audio amplifier debate bearing rotation noise microphone; <br>6, a rear bearing fixing transverse toggle stick, check the bearing wear loosening; <br>7, looseness is serious, the rotation excessive noise, there is a serious defect FAG bearing should be eliminated, replaced with the same type; <br>8, taking the amount of grease barrel (high dry yellow oil) with gentle heat to melt (not hot), detected through the bearing into immersed in the tub overflow no bubbles. Bearing grease removed before cooling, a small amount of residual grease. After cooling the grease removed angular contact ball bearings, the residual amount of grease. Determine how much residual amount of grease required. <br>9, wipe with a soft cloth or toilet paper bearing grease outside the FAG Bearings An undisturbed fitted to the pulley, maintenance work is completed.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
1, when the bearing sit until a certain period of time (or maintenance maintenance period), the bearings will be all removed;<br>2, with cleaning diesel or kerosene soaked cleaning bearings, if there are technical conditions are best to open the seal cover cleaning;<br>3, after cleaning air dry cleaning oil, appearance check for damage;<br>4, with a 150mm or so, the diameter of the angled contact ball bearing with an equal diameter of the wooden rod (preferably a hollow tube), one end fixed a bearing;<br>5, hand fast rotation of the bearing at the same time, the other end of the wooden rod (wood pipe) on the ear or audio amplifier microphone to listen to the bearing rotation noise;<br>6, fixed bearings after the lateral move the wooden rod, check whether the bearing wear loose phenomenon;<br>7, loose serious, excessive rotation noise, there are serious defects of FAG bearings should be eliminated, to the same model of replacement; 8, take a bucket will be the appropriate amount of grease (high-quality yellow dry oil) with a fire melting (not overheated), the detected bearings into the barrel soaked until no bubble overflow. Remove the bearings before the grease cools down, and the amount of residual grease is small. After the grease is cooled, the angle contact ball bearing is removed, and the amount of residual grease is high.<br>Determine the amount of grease residue as needed. 9, with a soft cloth or toilet paper to wipe the outside of the bearing grease will BE FAG bearings installed in place on the sheave, maintenance work is over.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
1. When the bearing runs to a certain period (or maintenance period), remove all the bearings;<br>2. Soak the bearings in diesel or kerosene for cleaning. If there are technical conditions, it is better to open the sealing cover for cleaning.<br>3. Air dry the cleaning oil after cleaning, and check the appearance for damage;<br>4. Use a wooden bar (preferably hollow tube) with a diameter of about 150 mm and equal inner diameter of angular contact ball bearing, and fix a bearing at one end;<br>5. While rotating the bearing quickly by hand, put the other end of the wooden bar (wooden tube) on the ear or the audio amplifier microphone to listen to the bearing rotation noise;<br>6. After fixing the bearing, move the wooden bar horizontally to check whether the bearing is worn or loose;<br>7. Fag bearings with serious looseness, excessive rotating noise and serious defects shall be eliminated and replaced with the same model;<br>8. Take a bucket and melt a proper amount of lubricating grease (high-quality yellow dry oil) with mild fire (do not overheat), and immerse the tested bearing in the bucket until no bubble overflows. Take out the bearing before the grease cools, and the amount of residual grease is small. Take out the angular contact ball bearing after the grease is cooled, and there is a lot of residual grease. Determine the amount of grease residue as required.<br>9. Clean the grease outside the bearing with soft cloth or toilet paper and assemble the fag bearing on the pulley as it is, and the maintenance work will be finished.<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: