由于皮带轮和齿轮在手册上查得轮孔直径必须大于20,而轴又要与轴承配合,故轴承的轴颈之间采用同一轴颈,而齿轮与齿轮及齿轮与轴承之间由于有凸沿,的英语翻译

由于皮带轮和齿轮在手册上查得轮孔直径必须大于20,而轴又要与轴承配合,

由于皮带轮和齿轮在手册上查得轮孔直径必须大于20,而轴又要与轴承配合,故轴承的轴颈之间采用同一轴颈,而齿轮与齿轮及齿轮与轴承之间由于有凸沿,所以每根轴采用同一尺寸,这样可以简化轴的加工工序,更便于维修和装配,所以轴和齿轮轮孔均采用d=45mm,四个轴的轴承均采用45mm的轴承。由于本机所能承受的弯力较小,故弯矩进行校核无必要,只需进行必要的扭矩校核。
0/5000
源语言: -
目标语言: -
结果 (英语) 1: [复制]
复制成功!
Since the diameter of the pulley and the gear hole must be greater than 20 in the manual, and the shaft must be matched with the bearing, the same journal is used between the journals of the bearings, and there is a convex edge between the gear and the gear and between the gear and the bearing. Therefore, each shaft adopts the same size, which simplifies the processing procedure of the shaft and is more convenient for maintenance and assembly. Therefore, the shaft and the gear wheel hole are all used d=45mm, and the bearings of the four shafts are all 45mm bearings. Since the bending force that this machine can bear is small, it is not necessary to check the bending moment, only the necessary torque check is required.
正在翻译中..
结果 (英语) 2:[复制]
复制成功!
Because the belt wheel and gear in the manual to find that the diameter of the wheel hole must be greater than 20, and the shaft and bearing matching, so the bearing between the shaft neck using the same shaft neck, and gear and gear and gear and bearing between the convex edge, so each shaft using the same size, so can simplify the shaft processing process, more convenient for maintenance and assembly, so the shaft and gear wheel holes are d- 45mm, four-axis bearings are 45mm bearings. Because the bending force that can be tolerated by this machine is small, it is not necessary to do the bending moment, only the necessary torque core.
正在翻译中..
结果 (英语) 3:[复制]
复制成功!
As the diameter of pulley and gear in the manual must be greater than 20, and the shaft must be matched with the bearing, so the Journal of the bearing adopts the same journal. Because there is a convex edge between the gear and gear and between the gear and the bearing, each shaft adopts the same size, which can simplify the processing procedure of the shaft, and is more convenient for maintenance and assembly. Therefore, d = 45mm is adopted for the shaft and gear wheel hole The bearings of the four shafts are 45mm. Because the bending force the machine can bear is small, it is not necessary to check the bending moment, just the necessary torque check.<br>
正在翻译中..
 
其它语言
本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.

Copyright ©2024 I Love Translation. All reserved.

E-mail: