针对牵引车型：终检需提供故障车或问题视频、照片及车型针对卡滞问题拉动主

For traction models: The final inspection needs to provide faulty cars or problem videos, photos and models. For <br>the stuck problem, pull the supervisor design and AUDIT for review. Standards are agreed. <br>Incorporate the problem of the side sign lights/side turn signals/signal lights not being integrated into the comprehensive control, and South Square confirms the repair status. <br>Temporary inspection standards are formed according to the way of dropping, and the inspectors are trained to focus on controlling the dropping phenomenon. Statistics the failure rate. <br>In response to the problem of abnormal sound of door opening and closing, it is required to feedback the fault point video to the improvement group to <br>organize external inspection, procurement, and R&D to evaluate together according to the supplier, and improve <br>according to the evaluation situation. According to the summary of electrical problems, the two ends of the connector Check the quality of the parts <br>. The problem that the lock hook cannot be screwed requires external inspection to pull the supplier's on-site service. The external inspection of the lock hook pulls the supplier's guarantee, and controls the incoming parts according to the size requirements marked on the drawing. (On-site inspection for unqualified products) <br>Compare and check the complete set of faulty and non-faulty parts of the faulty car. <br>"Project transfer to manufacturing. <br>1. Make OK standards for the wiring harness rubber cap installation, and pull the quality to confirm on the spot. <br>2. The harness is not installed in place. "100% online repair" <br>pulls the designer to confirm the problem. If increasing the torque value can eliminate the problem, it is recommended to write a contact form to request the design to change the torque requirements. <br>Re-receipt the project and issue an improvement plan by next Tuesday. <br>Organize the general assembly and quality personnel to conduct trial assembly review according to the trial assembly plan, and issue a change order after the verification measures are qualified. <br>Re-evaluate the problem of abnormal noise at the junction after the car, and issue an improvement plan to <br>implement the second trial installation time, and organize relevant personnel to conduct a trial installation review <br>technology to determine whether the film needs to be distinguished between winter and summer. If necessary, Clarify the difference between the two states and whether there is a difference in adhesive strength. <br>Provide an upgrade report for <br>procurement , and upgrade the problem. Procurement Department organizes relevant units to conduct a sample review of the film.

For towing models: Final inspection requires video of the faulty car or problem, photos and models<br>Review the supervisor design and AUDIT for the stuck issue. Standards are agreed upon.<br>The side sign/side turn light/profile light is not on and controlled in a comprehensive manner, and the South Square confirms the repair status.<br>According to the shedding mode to form a temporary inspection standard, training inspectors to focus on the phenomenon of shedding control. Statistics of shedding failure rate.<br>Request feedback into the improvement group of video shots of fault points for door opening and closing noise<br>Organization of out-of-country inspection, procurement, research and development together by supplier assessment, according to the assessment of the situation to improve<br>Check the quality of components at both ends of the plug based on the summary electrical class problems<br>The problem with the lock hook not moving requires the external inspection to pull the supplier's on-site service. Lock hook dimension inspection pull supplier guarantee, and in accordance with the dimensions indicated in the drawings to control the incoming parts. (On-site inspection of non-conforming products)<br>Compare and inspect the faultvehicle to remove the whole fault and the non-fault parts<br>"Project-to-manufacturing<br>1, for the harness rubber cap installation to develop OK standards, and pull the quality of on-site confirmation<br>2, the harness is not installed in place requirements 100% online repair"<br>Pull the designer to confirm the problem, such as increasing the torque value can eliminate the problem, it is recommended to write a contact order to request the design change torque requirements.<br>Re-receipt for the project and an improvement plan is issued by next Tuesday.<br>Organization of assembly and quality personnel according to the trial installation plan for test-loading review, verification measures qualified after the release of change orders.<br>Re-evaluate the noise issue at the back of the car and produce an improvement plan<br>Implement the second trial installation time, and organize relevant personnel to carry out trial installation review<br>Technically clear whether the film needs to distinguish between winter and summer states, if necessary, to clarify the difference between the two states and whether there is a difference in the paste force<br>Purchases provide upgrade reports to upgrade issues<br>The purchasing department organizes the relevant units to conduct a sample review of the film

For traction vehicles: video, photos and models of faulty vehicles or problems shall be provided for final inspection<br>Pull the supervisor design and audit to review the sticking problem. Standards are agreed.<br>The problem that the side marker lamp / side turn signal lamp / position lamp is not on will be brought into comprehensive control, and the South Square will confirm the repair status.<br>The temporary inspection standard is formed according to the falling off mode, and the inspectors are trained to control the shedding phenomenon. The falling failure rate was counted.<br>To solve the problem of abnormal sound when the door is opened and closed, it is required to take video of the fault point and feed it back to the improvement group<br>Organize external inspection, procurement, R & D together to evaluate the supplier, and improve according to the evaluation<br>Check the quality of the parts at both ends of the connector according to the summarized electrical problems<br>The problem that the locking hook cannot be screwed requires external inspection to pull the supplier to provide on-site service. The external inspection of lock hook size shall pull the supplier's guarantee, and control the incoming parts according to the size requirements indicated in the drawing. (there are unqualified products in the on-site investigation)<br>The whole set of fault parts and non fault parts are compared and checked<br>"Project to manufacturing<br>1. Make OK standard for the installation of wire harness rubber cap, and confirm the pull quality on site<br>2. Wiring harness not installed in place requires 100% on-line repair“<br>Pull the designer to confirm the problem. If the problem can be eliminated by increasing the torque value, it is suggested to write a contact list to require the design to change the torque requirements.<br>For the project re receipt, and issued the improvement plan before next Tuesday.<br>Organize the general assembly and quality personnel to carry out trial assembly review according to the trial assembly plan, and issue the change order after the verification measures are qualified.<br>The abnormal noise at the lap joint after landing is reevaluated and the improvement scheme is provided<br>Implement the second trial assembly time, and organize relevant personnel to carry out trial assembly review<br>Technology to determine whether the film needs to distinguish between winter and summer, if necessary, the difference between the two states and whether there is difference in adhesion force<br>Purchasing provides upgrade report to upgrade the problem<br>The purchasing department shall organize relevant units to review the sealing sample of the film<br>