主要分2种情况， 预处理影响+“不可控”因素。等待预处理开始供奶或者开

There are two main situations, pretreatment influence + "uncontrollable" factors. <br>The time to wait for the pretreatment to start milk supply or the start of CIP/disinfection is a special technical shutdown; <br>Note 1: No matter what causes the waiting for feeding problem, it belongs to the special technical shutdown. <br>Note 2: The filling worker in front of a certain filling line is not clear about the cause on the spot. This often requires the planner and the pre-processing team leader to discuss together to distinguish the real cause of waiting for milk and waiting for CIP (sometimes, It may be a chain reaction caused by the technical downtime of other machines in the later section. Sometimes, it may really just be that a pre-processing operator has made a short run and forgot to configure the acid-base solution). Therefore, don't leave difficult problems to the filler who drives a certain machine to solve, just put it in the waiting for milk, waiting for CIP, that is, the special technical shutdown. <br>●Under the requirements of the factory’s quality documents, the production equipment will be cleaned from time to time (such as cleaning sheet debris, cleaning heat seal residue, cleaning cutter residue, cleaning nozzles, etc.); <br>●Quality defective raw materials or Quality problems (caused by raw materials) found after packaging materials (such as packaging materials, fruit particles, flavors, etc.) on the machine; <br>●Short stop of the machine when replacing similar packaging material rolls without replacement. For example: replacing standard molds or other packaging materials (labels, films, sheets, cartons, etc.), which is also a bottleneck of the machine, which must be shut down to complete; <br>●Can change: In the case of non-replacement, due to can change The short stop is included in the special technical stop. <br>●Due to the incompatibility between product features and machine functions, the time lost when running the production line at a lower speed. <br>Note 1: Special technical shutdown refers to how much the shutdown has to do with technology. This type of shutdown often requires some technical transformation (still a key improvement target of the equipment department/engineering department) before it can be significantly reduced.

主要分2种情况， 预处理影响+“不可控”因素。<br>等待预处理开始供奶或者开始 CIP/消毒的时间都属于特殊技术停机； <br>注1： 无论是什么原因造成的等待供料问题，都归属在特殊技术停机内。 <br>注 2：在某条灌装线前的灌装工当场是不清楚产生原因的，这往往需要计划员和前处理组长一起探讨才能分清楚导致后面等奶、等CIP的真实原因（有时，可能是后工段的其他机器的技术停机导致的连锁反应。有时，可能真的只是某一个前处理操作工开了一个小差忘记配置好酸碱溶液了）。所以，别把有难度的问题交给开某一台机器的灌装工来解决，放在等奶、等CIP里，也就是特殊技术停机里即可。 <br>●工厂的质量文件要求下，生产不定期会做的设备清洁（例如清理片材碎屑，清理热封残胶，清理切刀残胶，清理喷头，等等）； <br>●有质量缺陷的原材料或包装材料（例如包材、果粒、香精等）上机后发现的质量问题（由原辅料引起）；<br>●非换品情况下的更换同类包材卷时机器的短停。例如：更换标模或其他包材（标、膜、片材、纸盒等），这也是该机器的一个瓶颈，必须停机才可以完成； <br>●换罐: 非换品情况下，由于换罐导致的短停，计入特殊技术停机。<br>●由于产品特性与机器功能不兼容, 以较低的速度运行产线时损失的时间。 <br>注1：特殊技术停机指的是这个停机多少与技术有关系，这类的停机，往往需要通过一些技改（仍然是设备部门 / 工程部门的重点改善对象），才可以比较明显地降低。

There are two main cases, pretreatment effect + uncontrollable factors.<br>The time waiting for pretreatment to start feeding milk or CIP / disinfection belongs to special technical shutdown;<br>Note 1: no matter what the cause of waiting for feeding problem, it belongs to special technical shutdown.<br>Note 2: the filling workers in front of a certain filling line are not clear about the causes on the spot, which often requires the planner and the pre-treatment team leader to discuss together to identify the real causes of waiting for milk and CIP (sometimes, it may be the chain reaction caused by the technical shutdown of other machines in the later section). Sometimes, it may be that a pretreatment operator made a short trip and forgot to prepare the acid-base solution). Therefore, do not give the difficult problems to the filling workers who open a certain machine to solve, put them in the waiting milk, CIP, that is, special technology shutdown.<br>Equipment cleaning (such as cleaning sheet debris, cleaning residual glue of heat seal, cleaning residual glue of cutter, cleaning nozzle, etc.) which will be done irregularly under the requirements of factory quality documents;<br>The quality problems found in the raw materials or packaging materials (such as packaging materials, fruit granules, flavors, etc.) after being found on the machine (caused by raw materials).<br>● short stop of the machine when replacing the same kind of packaging coil without changing the product. For example: to replace the standard mold or other packaging materials (standard, film, sheet material, carton, etc.), which is also a bottleneck of the machine, it can only be completed by stopping the machine;<br>● tank replacement: under the condition of non replacement, the short-term shutdown caused by tank replacement is included in the special technical shutdown.<br>● time lost when running the production line at a lower speed due to incompatibility between product characteristics and machine functions.<br>Note 1: special technical shutdown refers to that the shutdown is related to technology. This kind of shutdown can be significantly reduced by some technical transformation (which is still the key improvement object of equipment department / Engineering Department).<br>