根据《实用供热空调设计手册》第1989页可知，确定计算管段的冷水量时，

根据《实用供热空调设计手册》第1989页可知，确定计算管段的冷水量时，可以根据管路所连接末端设备（如AHU、FCU等）的额定流量进行叠加计算。但必须注意，当总水量达到与系统总流量（水泵流量）相等时，干管的水量不应再增加。计算管道沿程阻力时，单位长度摩擦压力损失（比摩阻）宜控制在100~300Pa/m，通常最大不应超过400Pa/m

0/5000

源语言: -

目标语言: -

结果 (英语) 1: [复制]

复制成功！

According to page 1989 of the "Practical Heating and Air Conditioning Design Manual", when determining the calculation of the cold water volume of the pipe section, the superimposed calculation can be performed according to the rated flow of the terminal equipment (such as AHU, FCU, etc.) connected to the pipeline. However, it must be noted that when the total water volume is equal to the total system flow (water pump flow), the water volume of the main pipe should not be increased. When calculating the resistance along the pipeline, the friction pressure loss per unit length (specific friction resistance) should be controlled at 100 ~ 300Pa / m, usually the maximum should not exceed 400Pa / m

正在翻译中..

结果 (英语) 2:[复制]

复制成功！

According to page 1989 of the Practical Heating Air Conditioning Design Manual, when determining the amount of cold water in the pipe segment, the calculation can be calculated according to the rated flow rate of the end equipment (e.g. AHU, FCU, etc.) connected to the pipe. It is important to note, however, that the amount of water in the main pipe should not increase when the total amount of water is equal to the total flow of the system (pump flow). When calculating the flow resistance of the pipe, the unit length friction pressure loss (than momo resistance) should be controlled at 100 to 300Pa/m, usually the maximum should not exceed 400Pa/m

正在翻译中..

结果 (英语) 3:[复制]

复制成功！

According to page 1989 of practical heating and air conditioning design manual, when determining the cold water volume of the pipe section, it can be calculated by superposition according to the rated flow of the terminal equipment (such as AHU, FCU, etc.) connected to the pipe. However, it must be noted that when the total water volume is equal to the total flow of the system (pump flow), the water volume of the main pipe shall not be increased. When calculating the resistance along the pipeline, the friction pressure loss per unit length (specific friction resistance) should be controlled within 100 ~ 300pa / m, and the maximum value should not exceed 400pa / m generally<br>

正在翻译中..

其它语言

本翻译工具支持: 世界语, 丹麦语, 乌克兰语, 乌兹别克语, 乌尔都语, 亚美尼亚语, 伊博语, 俄语, 保加利亚语, 信德语, 修纳语, 僧伽罗语, 克林贡语, 克罗地亚语, 冰岛语, 加利西亚语, 加泰罗尼亚语, 匈牙利语, 南非祖鲁语, 南非科萨语, 卡纳达语, 卢旺达语, 卢森堡语, 印地语, 印尼巽他语, 印尼爪哇语, 印尼语, 古吉拉特语, 吉尔吉斯语, 哈萨克语, 土库曼语, 土耳其语, 塔吉克语, 塞尔维亚语, 塞索托语, 夏威夷语, 奥利亚语, 威尔士语, 孟加拉语, 宿务语, 尼泊尔语, 巴斯克语, 布尔语(南非荷兰语), 希伯来语, 希腊语, 库尔德语, 弗里西语, 德语, 意大利语, 意第绪语, 拉丁语, 拉脱维亚语, 挪威语, 捷克语, 斯洛伐克语, 斯洛文尼亚语, 斯瓦希里语, 旁遮普语, 日语, 普什图语, 格鲁吉亚语, 毛利语, 法语, 波兰语, 波斯尼亚语, 波斯语, 泰卢固语, 泰米尔语, 泰语, 海地克里奥尔语, 爱尔兰语, 爱沙尼亚语, 瑞典语, 白俄罗斯语, 科西嘉语, 立陶宛语, 简体中文, 索马里语, 繁体中文, 约鲁巴语, 维吾尔语, 缅甸语, 罗马尼亚语, 老挝语, 自动识别, 芬兰语, 苏格兰盖尔语, 苗语, 英语, 荷兰语, 菲律宾语, 萨摩亚语, 葡萄牙语, 蒙古语, 西班牙语, 豪萨语, 越南语, 阿塞拜疆语, 阿姆哈拉语, 阿尔巴尼亚语, 阿拉伯语, 鞑靼语, 韩语, 马其顿语, 马尔加什语, 马拉地语, 马拉雅拉姆语, 马来语, 马耳他语, 高棉语, 齐切瓦语, 等语言的翻译.